VeEX UX400 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 209

background image

6.3 RFC2544

Overview:

RFC 2544 recommendations are well accepted in the test and measurement industry for network performance testing. The RFC 2544 test suite consists of and performs a

set of four automated tests (throughput, latency, frame loss, and burst or back-to-back) to qualify the performance of a network link under test. The tests are especially

popular for the verification of network links with certain service level agreements (SLA).

The following settings must be configured prior to RFC 2544 testing:

Test layer (Layer 2 & 3)

Frame header (MAC, VLAN, IP, UDP, and Data)

Test frames selection

Pass/fail thresholds (optional)

Throughput

Latency

Frame loss

Burst (back-to-back)

RFC2544 Header Setup (Layer 2)

6.3.1 Setup

Unless otherwise noted, the Frame Header and related setups are identical to the setups described in the BERT Application. A summary of the RFC 2544 setup options are

outlined below.

6.3.1.1 Header Settings

Profile:

Load a previously configured test profile or create a new profile from existing settings. Currently its set to "Default".

Test Layer:

Select the test layer to perform the test. Options are Layer 2, Layer 3 or Layer 4.

Frame Type:

Select the Ethernet frame type for Layer 2 or Layer 3.

Layer 2:

Ethernet II (DIX) (named after DEC, Intel, and Xerox, this is the most common frame type today),

802.3 Raw (IEEE 802.3 frame without LLC) - Not available when Layer 3 is selected

Layer 3: Ethernet II (DIX)

VLAN:

Off, 1 tag, 2 tags, 3 tags

Up to three VLAN tags (VLAN stacking for Q-in-Q applications) can be configured.

Note:

VLAN stacking is an option.

MPLS

(only for Layer 3 & 4)

:

Off, 1 tag, 2 tags, 3 tags

Up to three MPLS tags can be configured.

Note:

MPLS tag configuration is only available when the MPLS option is purchased.

PROTOCOL

(Only for Layer 4)

:

UDP or TCP

RFC2544 Header Setup Layer 3

RFC2544 Header Setup Layer 4

UX400 10G e-Manual D07-00-058P RevA00

Page 57 of 209

«
...
55
56
57
58
59
...
»

Содержание UX400


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для UX400

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: UE Страницы: 4

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: Zolix Instruments Страницы: 22

Бренд: Eaton Страницы: 12

Бренд: Saga Страницы: 9

Бренд: Harsco Industrial Страницы: 57

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 2

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

Бренд: Multi-Clean Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды