manualshive.com logo in svg

VeEX MTTplus-522 OSP+, Руководство пользователя, Страница: 10 / 43

Поделиться
Скачать
VeEX MTTplus-522 OSP+ Скачать руководство пользователя страница 10

4.0 Basic Operation

For information on Basic Operations, Home menu, Launching Test Applications, and other features specific to the MTTplus Host

Chassis, refer to the

 

MTTplus Platform Manual

. The following sections describe basic operations for the MTTplus-522 module.

4.1 Touch-Screen Display

The LCD supports touch-screen operation. To operate the touch-screen, use the stylus located in the top cover to navigate the

menus and tabs. Please observe the following precautions:

Never use excessive pressure on the touch-screen as this may damage its functionality.

Never use sharp objects such as a pen, screwdriver etc. as this may damage the surface.

Clean the surface of the touch screen using a soft cloth and mild detergent only. Do not use alcohol.

Go back to top

 

Go back to TOC

4.2 Battery

The MTTplus chassis is equipped with an intelligent Li-ion rechargeable battery pack which is located in the rear of the unit. The

battery will be partially charged upon delivery, so it is recommended to charge the battery fully before use. Please charge the battery

at room temperature to preserve its life and to obtain maximum charge. The battery is charged during operation provided the unit is

connected to the AC Mains using the supplied AC adapter. Removing the battery, while the unit is powered on is not recommended -

this may result in damage. Charge the battery by connecting the AC Main adapter to the power jack on the left side.

Go back to top

 

Go back to TOC

4.3 Connector Panel

The MTTplus-522 module supports:

RJ11 LINE interface for G.fast and DSL

RJ45 Ethernet Port, for DSL to PC Pass Through mode

TIP/A, RING/B, GND/E 2mm Mini Banana

Connector Panel

Go back to top

 

Go back to TOC

MTTplus-_Test_Module

Page 11 of 44

Содержание MTTplus-522 OSP+












































Отзывы:

Нет отзывов