background image

Wiring/Miscellaneous For TLS-IB Consoles W/RS-232 & With & W/O IFSF)

Troubleshooting

4-12

Figure 4-8.   Replacing PROM Chip 

REPLACING THE POWER SUPPLY BOARD

When to Replace the Power Supply Board

The Power Supply board must be replaced either when:

• Probe data is not being processed. (You can check the Probe Status Indicator [LED1 - see Figure 4-6 on 

page 4-10] to verify that the probe is communicating with the TLS-IB. If LED1 is flashing, the CPU is acquiring 
valid probe data), or,

• The voltage between the GND and 8V test points (Figure 4-5 on page 4-8) on the back of the CPU board is 

less than 7 Vdc.

How to Replace the Power Supply Board

1.

To replace the Power Supply board, turn Off power to the system.

2.

Disconnect the CPU cable from the Power Supply board.

3.

Tag and disconnect probe, power, and overfill alarm relay wiring to the Power Supply board.

4.

The Power Supply board is secured by two T-15 Torx screws in the top of the board. After removing the Torx 
screws, slowly lift up on the board until the lower tabs on the board clear the slots in the bottom of the TLS-IB, 
then continue to lift the board out.

Y2

NODE

ADDRESS

12

34

Y3

TLS-IB CPU BOARD

PROM chip (U29)

S1

STATIC SENSITIVE - WEAR 
GROUNDED ANTI-STATIC 
WRIST STRAP BEFORE 
HANDLING THIS BOARD!

1) Orient PROM so that the small indented dot on
top of the chip is on the same side with the small
triangle embossed in the socket's base; or,  
2) If the chip is covered with a label you can also orient 
the chip correctly if you insert the chip in the socket
with its angled corner in the same angled corner of the 
socket. 
3) Carefully align the chip's pins with the socket's pins.  
(If you have the pins aligned correctly, the chip will seem to 
drop into the socket.)  Then push down firmly and evenly 
on the chip until it snaps into the socket.  
4)  Check to see that all pins are in place and none are bent.
 

OFF

Содержание TLS Series

















































Отзывы: