background image

Introduction

Precautions Against Static Electricity

3

Precautions Against Static Electricity 

Before removing electronic components from their anti-static bags read the following static electricity precautions.

1. Before handling any components, discharge your body's static electric charge by touching a grounded surface 

such as the TLS-450PLUS console’s case.

2. Do not remove parts from their anti-static bags until you are ready to install them.

3. Do not lay parts on the anti-static bags! Only the insides are anti-static.

4. When handling parts, hold them by their edges and their metal mounting brackets. 

5. Never slide parts over any surface.

6. Avoid plastic, vinyl, and Styrofoam in your work area.

Before Turning Off Power

Before powering off the console perform a system backup:

1. Beneath the left side of the TLS-450PLUS console, locate the USB module and insert the V-R Backup thumb 

drive, minimum 4 GB, (P/N 332970-004) into one of the external USB ports, P/N 333477-001 (see item 3 in 
Figure 1).

WARNING

This system operates on 120/240 Vac power. Serious injury or death from 
electrical shock could occur if the power ON/OFF warnings in this manual are not 
heeded. 

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY 
PRECAUTIONS COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, 
RESULTING IN SERIOUS INJURY OR DEATH.

1. Read and follow all instructions in this manual, including all safety warnings.

2. Remove rings from hands, metal watch bands and bracelets, and loose 

hanging neck jewelry before performing these procedures. 

3. Do not modify or use service parts other than those provided by Veeder-

Root. 

LEGEND FOR NUMBERED BOXES IN 

Figure 1

1.

Front of console

2.

Ethernet Interface Module

3.

USB Ports on USB module

Figure 1.   USB Module - USB ports

OFF

3

2

1

Содержание TLS-450PLUS

















Отзывы: