background image

12

  Installing Software Features

Before installing a software feature upgrade, perform a system backup using a V-R Backup thumb drive (P/N 
332970-004) following the procedure described in “Before Turning Off Power” on page 3. 

The V-R Backup thumb drive is different from a V-R Software Upgrade thumb drive - the two 
are not interchangeable.

Software Features Installation Procedure

1. Get the USB Adapter and upgrade i-button from the upgrade kit. Remove the plastic end cap from the USB 

Adapter and Insert the i-button in the adapter as shown in Figure 7 below.

Figure 7.   Inserting iButton Into USB Adapter

2. Replace the plastic retaining cap on the adapter after inserting the i-Button.

3. Plug the USB Adapter into one of the two USB ports in the console's USB module (see Figure 1).

4. From the Home Screen, touch the following: 

Menu>Software Upgrade>Upgrade Features

.

5. When you have completed the Upgrade Features procedure remove the upgrade thumb drive.

6. With the new software features installed, perform a system backup using the V-R Backup thumb drive (P/N 

332970-004) as discussed in “Before Turning Off Power” on page 3. 

The V-R Backup thumb drive is different from a V-R Software Upgrade thumb drive - the two 
are not interchangeable.

LEGEND FOR NUMBERED BOXES IN Figure 7

1.

USB ada

p

ter

2.

i-Button

3.

Insert i-Button, large end u

p

NOTICE

1

2

3

954-11.eps

NOTICE

Содержание TLS-450PLUS

















Отзывы: