background image

Mounting Instructions

Mounting Instructions

5

Figure 2.   Acknowledgment Switch Mounting Dimensions

Mounting Instructions

Overfill Alarm

1. Select a mounting location where the Overfill Alarm can be seen and heard clearly from the area where the 

fuel tanks are filled. In addition, consider the ease of routing interconnection conduit. 

2. Locate and mark mounting holes using the hole pattern in Figure

 

1.

3. Mount the Overfill Alarm using the four mounting tabs on the housing. 

Acknowledgment Switch

1. Select a mounting location where the Acknowledgment Switch can be easily activated by the tank truck driver. 

In addition, consider the ease of routing interconnection conduit. 

2. Locate and mark mounting holes using the hole pattern in Figure

 

2.

3. Mount the Acknowledgment Switch using the four mounting tabs on the housing. 
4. Install conduit between the Acknowledgment Switch, Overfill Alarm, and TLS Console. 

RESET

ACKNOWLEDGE

VEEDER-ROOT

2'' (50.8 mm)

4.3'' (109.5 mm)

2'' (50.8 mm)

6.75"

(171.5 mm)

1.4 ''

(35.6 mm)

1/2 ''

conduit

connector

3'' (76.2 mm)

1'' (25.4 mm)

Hinge

side

TEST button

(on side)

0.313'' (8 mm) dia. 

4 holes

Содержание Overfill Alarm















Отзывы: