background image

11

  Console Installation

Console Location

For console location, refer to the ‘System Consoles’ section of manual 577013-578 on the Veeder-Root Tech Docs 
CD-ROM prior to installing the 8601 Series Console. 

Mounting the Console

To mount the console remove the two T15 screws in the bottom of the cover (see Figure 1). As you lift up the 
bottom of the cover it pivots on two tabs that project from the top of the console’s chassis into slots in the top of 
the cover. Lift the cover off the chassis tabs and set it aside. Notice the corner mounting holes in the base of the 
chassis (Item 12 in Figure 2). Locate the chassis on the wall in the desired mounting location, mark the hole 
locations, drill the appropriate pilot holes; and using 1/4-inch (6mm) maximum fasteners (customer supplied), 
attach the chassis to the mounting surface at all four locations. 

Figure 1 shows the two designated knockouts through which power wiring can safely enter the console.

Wiring the Console

The 8601 Series Console can be operated using either AC or DC power.

WARNING

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY PRECAUTIONS 
COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, RESULTING IN SERIOUS 
INJURY OR DEATH.

Explosive vapors or flammable liquids could be present near locations where fuels are 
stored or being dispensed. 

This console is not explosion proof. Do not install this console in a volatile, combustible, 
or explosive atmosphere. 

An explosion or fire resulting in serious injury or death, property loss and equipment 
damage could occur if the console is installed in a volatile, combustible or explosive 
atmosphere (Class I, Division 1 or 2).

WARNING

This console contains high voltages which can be lethal. It is also connected to low 
power devices that must be kept intrinsically safe.

1. Turn power off at the circuit breaker. Do not connect the console AC power 

supply wires at the breaker until all devices are installed.

2. Attach conduit from the power panel to the console's Power Area 

knockouts only.

Connecting power wires to a live circuit can cause electrical shock that may result in 
serious injury or death. 

Routing conduit for power wires into the intrinsically safe compartment can result in fire 
or explosion resulting in serious injury or death

OFF

Содержание 8601 Series










































Отзывы: