background image

 

Dispenser Junction Box Requirements

Installing the Dispenser Pan Sensor

4

Dispenser Junction Box Requirements

Installing Dispenser Control Interface

1.

The dispenser junction box must have at least one unused threaded conduit open-
ing, either 1/2”, 3/4”, or 1” trade size.

2.

The opening may be anywhere on the junction box, as long as sufficient clearance 
exists around the opening for installation of the Dispenser Control Interface.

Important 

When determining the installation location of the Dispenser Control Interface on the 
junction box, choose a location in which the Dispenser Control Interface will not 
interfere in any way with the operation of the dispenser or in maintenance or service 
access.

Wiring Dispenser Control Interface to Dispenser

The following requirements must be met before attempting to wire the Dispenser 
Control Interface to a dispenser.

1.

Be sure AC power to the dispenser junction box is OFF before attempting to open 
the junction box and wire the dispenser control interface to the dispenser.

The following applies to 

both

 installing and wiring the Dispenser Control Interface:

Important 

2.

The junction box must have sufficient volume to accommodate the extra wiring to 
be installed, and must comply with the National Electric Code, Article 370-16. The 
required volume for any dispenser can be calculated using the information in Table 
I.

WARNING

Before installing this device, turn OFF power to the system.

Electrical shock resulting in serious injury or death may result if 
power is on during installation and the device is improperly installed. 

High voltages are present in the dispenser junction box. Be sure to 
turn OFF all power before opening the junction box. More than one 
disconnect may be required to completely de-energize the box. Failure 
to comply with this warning may result in personal injury, property 
loss, and equipment damage.

Do not use any electric tools in the area of the dispenser island. Since 
the island is considered a Class I, Group D Hazardous Location, 
failure to comply with this warning could result in an explosion.

OFF

Содержание 847990-001





















Отзывы: