Vectronic Aerospace Drop-Off Release Скачать руководство пользователя страница 11

Doc. No.: 

Release Transmitter User Manual 

Date: 

02.07.2019 

 
 
 

 

11 

 

 

Design is the property of VECTRONIC Aerospace GmbH.                                               

Unauthorized duplication or distribution to a third party is prohibited. 

For using the software, please refer to the GPS PLUS Drop-Off Manager manual. You 
need to connect the transmitter to a PC for the following tasks: 

  to  register  a  drop-off  on  the  transmitter;  this  is  necessary  to  enable 

communication with this drop-off 

  to change configuration of a drop-off 

  to upload new firmware to the drop-off 

If you use the transmitter as interface between PC and drop-off, the drop-off needs to 
be within a few meters of the transmitter and you must be able to detach and attach 
the magnet to the drop-off. 

7  Drop-off list 

When  you  switch  on  the  transmitter,  it  will  automatically  give  a  list  of  all  drop-offs 
registered  on  the  transmitter.  The  drop-off with  the  lowest  number  will  be  displayed 

first. Move upwards and downwards this list with the Up 

 and Down 

 buttons. 

8  Configuring drop-offs or upload new firmware 

To configure a drop off, to change the release settings, or to upload new firmware, the 
transmitter needs to be connected to the PC with the GPS PLUS Drop-Off Manager 
program opened. For details please refer to the GPS PLUS Drop-Off Manager manual. 

9  Releasing a radio drop-off 

The main feature of the release transmitter is to release a radio-and-timer-controlled 
drop-off on  demand.  The  maximum  range  for  this  is  500  m.  If  possible,  release  the 
drop-off while you can see the animal. 

Note

: Prior to preparing the drop-

off release make sure the transmitter battery’s 

voltage is higher than 4.05 Volt. Otherwise there might not be enough power to 
reach the drop-off. Ideally, the battery voltage would be close to 5.0 Volt.   

Note:

 

Connect  the  correct  antenna  to  the  device.  A  wrong  or  missing 

antenna can damage the device as the strong signal can’t be transmitted 
but discharges internally!

  

Note

: It is possible that the animal will be startled when the collar is released 

and  drops  down.  Avoid  triggering  the  drop-off  if  the  animal  is  in  a  situation 
where it could get hurt by erratic movements (e.g. on a cliff edge). 

Содержание Drop-Off Release






















Отзывы: