W
e at Vectra Fitness appreciate your selecting our On-Line
®
1400 for your fitness
program, and invite your questions and comments. We're sure that you’ll be pleased
with your new Vectra Fitness gym.
This owner’s manual provides you with safety rules, assembly instructions and
routine inspection and maintenance information to enable you to get the most from
your gym. Please read through this manual carefully before you assemble and use your
On-Line
®
1400.
Safety Rules
Introduction
Routine Inspection
& Maintenance
Warning:
Serious injury can occur if you are struck by falling weights or moving parts. The
risk that you assume by using this type of equipment can be reduced by obeying
a few simple rules:
1.
IMPORTANT:
Cables are a wear item. It is your responsibility to prevent
unexpected breakage. To do this, inspect every cable daily. Pay particular
attention to areas near fittings at each end of each cable. Access panels are
provided, where necessary, for this purpose. Replace worn, frayed, or damaged
cables immediately. The actual wire strands, the fittings, and the nylon jacket
itself must all be scrutinized. Using or allowing a machine to be used with a
suspect cable can result in serious injury.
2. Inspect the nylon jacket of each cable carefully, again paying particular attention
to the cable ends. This nylon jacket is essential for cable life and safety. Any
cable should be replaced if the nylon jacket: is missing, is damaged in any
way, has pulled or shrunk away from the fittings at the end of the cable, or
is discolored. DISCOLORATION, DARKENING OR BULGING OF THE JACKET IS
AN EARLY INDICATION OF INTERNAL PROBLEMS SUCH AS WEAR OR FRAYING.
3. Read and follow all instructions in your owner’s manual, on your exercise chart,
and on product warning label. Additional copies are available from Vectra
Fitness, Inc. or your dealer. Do not use this machine until you have taken the
time to become completely familiar with its safe operation.
4. Consult your physician before beginning your exercise program.
5. Do not allow young children to use or play with or around this machine. Allow
older children to use the machine only with adult supervision.
6. Keep body, hair, and clothing clear of weights and moving parts at all times.
Keep fingers clear of moving parts while making adjustments.
7. Inspect the gym for loose or worn parts, damaged, frayed, or worn cables,
broken weight plates, etc. Do not use or allow the machine to be used until
any defective parts are repaired or replaced. Refer to the “Routine Inspection
and Maintenance” section of your manual for specific inspection rules. Use
only Vectra authorized replacement parts.
8. Ensure that the weight selector pin is in good working condition and fully
engaged in the selector shaft prior to lifting. Use only the Vectra supplied pin
or a Vectra authorized replacement.
9. Ensure that any locking mechanisms are properly engaged prior to lifting.
Locking mechanisms secure the following in position during use: seat pads,
accessory items such as squat attachments and lat hold downs, cable
attachments, press arms, leg developers, etc. An improperly engaged locking
mechanism could result in an injury.
10. Obtain assistance to free jammed weight plates, pulleys, etc. Do not attempt
to free jammed weight plates by yourself. Falling weight plates can cause
serious injury. Do not pin the weight stack or top plate in an elevated position
and do not use machine if found in this condition.
11. Do not drop the weight plates. Lift only as much as you can control safely.
Never use dumbbells or other means to incrementally increase the weight
resistance. Use only those means provided by Vectra. Don’t be careless, stay
alert.
12. Serious injury could result if equipment moves while in use. To prevent this,
ensure that the floor is even, strong, and not too slippery. If equipment slides
too easily on floor, place equipment on rubber matting. Errors in lifting form
could also result in bench moving in use. To prevent this, lift weight vertically
only and do not push horizontally with your feet while lifting.
Replace the warning label on product if damaged, illegible, or removed.
T
he Vectra On-Line
®
1400 is designed to provide years of trouble-free service
with minimal routine maintenance. You can be confident of continued top quality
performance by carrying out the following periodic inspection.
PERFORM THE FOLLOWING SAFETY CHECK DAILY:
1.
Inspect cables, cable ends and nylon jacket very carefully. Refer to Warning Label
for specific information on inspecting cables. This same information is repeated
in this manual and on your exercise chart.
Replace any damaged or worn
cables.
Annual cable replacement (semiannual in multi-user settings) is strongly
recommended as an additional precaution. The rate at which cables wear depends
on many factors including: repetitions, weight setting, misuse, abuse, etc. Because
of this, periodic cable replacement is not a sufficient safeguard against unexpected
breakage. Nothing short of a thorough, careful daily inspection constitutes an
adequate safety program.
PERFORM THE FOLLOWING CHECKS WEEKLY:
1.
Inspect frame and pulley bolts for tightness. Tighten if necessary.*
2.
Inspect accessory items (lat bar, curl bar, ankle strap, squart attachments. etc.)
for damaged mounting eyes, springs, broken stitches, etc. Replace any damaged
or worn items.
3.
Inspect weight selector pin for proper fit and retention in selector shaft. Replace
improperly functioning pin with Vectra replacement pin only.
4.
Inspect press arm adjustment lever for proper engagement. Replace improperly
functioning parts only with VECTRA replacement parts.
5.
Inspect press arm mounting screws for tightness. Tighten if necessary.*
6.
Inspect bench bolts. Tighten bolts if necessary.* Inspect bench wheel, wheel
suspension spring and bench feet. Replace any damaged or malfunctioning parts.
7.
Inspect leg developer screws and pivots for tightness and function. Inspect spring
and lever. Replace any damaged or malfunctioning parts.
8.
Inspect bench cushion latching mechanisms. Replace any damaged or
malfunctioning parts.
9.
Inspect cable retaining plugs and spring plungers. Replace if necessary.
10.
Inspect butterfly arm mounting screws for tightness. Tighten if necessary.*
11.
Inspect butterfly adjustment mechanism for proper function. Replace improperly
functioning parts only with VECTRA replacement parts.
12.
Adjust cable system tension if necessary (see assembly instructions for details).
13.
Inspect pad on bench that grips the frame tube (located near wheel). Inspect similar
pads on calf block. Replace any damaged or missing pads.
14.
Inspect high pulley member bolts for tightness. Tighten if necessary.
PERFORM THE FOLLOWING CHECKS MONTHLY:
1.
Inspect all foam hand grips, pads, etc. Replace any damaged, worn, or loose parts.
2.
Inspect weight plates for cracks, damaged bushings, etc. Replace if necessary.
Check bolt, tighten if necessary.
3.
Vectra’s stainless steel guide rods DO NOT REQUIRE LUBRICATION or anti-rust
treatment. Simply keep them free of grit, sticky or gummy sprays, etc.
4.
Clean upholstery with mild soap and water as desired.
5.
If unit is in a humid area, such as near a pool, hot tub or sauna, or in certain
climates, use of an auto wax should delay rusting.
Содержание On-Line 1400
Страница 1: ...Owner s Manual On Line 1 400...
