Vectra Fitness 175 Скачать руководство пользователя страница 12

Страница: 12 / 96

Page No. : 11

MANUFACTURING DATA AND DIMENSIONS

The following data of clearances and tolerances are given as a guide for personnel engaged in major overhauls

and the figures are those used in the factory for production purposes.

Cylinder Block

Height of cylinder block (Top to bottom faces)

… 13.743 / 13.740 inch (349. 085 / 349. 009 mm)

Parent bore dia. for Cylinder Liner

… 3.8583 / 3.8580 inch (98.022 / 98.000 mm)

Depth of Recess for Liner Flange (C.I. Liners)

… 0.157 / 0.155 inch (3.99/3.94 mm)

Dia Recess of Liner Flange (C.I. Liners)

… 4.0476 / 4.0437 inch (102.81/102.71 mm)

Main bearing parent bore

… 2.9175 / 2.9164 inch (74.105 / 74.080 mm)

No. 1 Bore for Camshaft

… 1.884 / 1.883 inch (47.865 / 47.840 mm)

No. 2 Bore for Camshaft

… 1.875 / 1.874 inch (47.625 / 47.600 mm)

No. 3 Bore for Camshaft

… 1.865 / 1.864 inch (47.375 / 47.350 mm)

No. 4 Bore for Camshaft

… 1.855 / 1.854 inch (47.125 / 47.100 mm)

No. 5 Bore for Camshaft

… 1.845 / 1.844 inch (46.865 / 46.840 mm)

Cylinder Liners – Cast Iron

Type …Production liner

… Dry – Interference fit

Service liner

… Dry pre finished transition fit.

Outside diameter of liner

… 3.861 / 3.860 inch (98.075 / 98.047 mm)

Interference fit of liner in Cylinder Block

… 0.003 / 0.001 inch (0.075 / 0.025 mm)

Inside dia. of finished liner in Cylinder Block

… 3.741 / 3.740 inch (95.022 / 95.000 mm)

Outside dia. of liner flange

… 4.040 / 4.037 inch (102.64 / 102.54 mm)

Flange thickness

… 0.158 / 0.157 inch (4.02 / 4.00 mm)

Liner protrusion above cylinder block
machined surface (Above top face of block)

… 0.003 / 0.0011 inch (0.080 / 0.030 mm)

NOTE : Reboring to oversize is not recommended

Pistons :

Type

… Alfin Piston with re-entrant bowl and valve pockets on

crown. Offset of combustion bowl in piston crown

should be to the FI Pump side while assembling piston

in engine. (Offset of valve pockets towards camshaft

side)

Piston Height above cylinder block top face

… 0.006 / 0.001 inch (0.150 / 0.025 mm)

(Above block surface)

Bore Dia. for Gudgeon Pin

… 1.2503 / 1.2501 inch (31.758 / 31.753 mm)

Top ring Groove Width

… 0.118 inch (3.0 mm) – Half Keystone ring

2nd ring Groove Width

… 0.080 / 0.079 inch (2.05 / 2.03 mm)

3rd ring Groove Width

… 0.159 / 0.158 inch (4.05/4.03 mm)

Содержание 175

































































































Результаты поиска

Содержание 175

Отзывы:

Vectra Fitness 175, Техническое руководство по двигателю, Страница: 12 / 96

Результаты поиска

Содержание 175

Отзывы: