background image

5

* Depending on version

TECHNICAL DATA

Following  data  is applied for CD4506,
CD4526X, CD4626X
• Temperature Range: - 2 0 ° C  ~   + 7 5 ° C.
• Power Supply:
-  12 V DC, - at GND.
-  Voltage Range: +10.5V~ +16 V.
-  Current Consumption:
-  About 1 A (about 0.1 A in off state)
•  Dimensions (w x h x d ): DIN Housing,180 x
    51 x 160 mm .

Warning: 
-  To prevent short-circuiting, disconnect the
   negative car battery terminal until the set has
   been mounted and connected (fig.1 See
   separate installation card).
-  Only trained specialists may install the unit.
-  Always observe correct assignment of vehicle
   connections. Incorrect assignment of the
   connections may lead to damage of the unit or
   vehicle electrical system/electronics.
-  Observe automotive industry quality standards.
-  Fire hazard! When drilling, care must be taken
   not to damage concealed wiring harnesses, the
   fuel tank and fuel lines.
-  Never drill into supporting or safety-relevant
   body parts.

INSTALLATION

Connection in vehicles equipped with
standard ISO connectors:
The radio may be installed without major
preparation in vehicles equipped with ISO
standard connectors. Some signals may have to
be adapted or connected to the ISO connectors
(see separate installation card).

Connection in vehicles without standard ISO
connectors:
F o r   v e h i c l e s   w i t h   d i f f e r e n t   c o n n e c t i o n
requirements, ask your dealer for an adapter
cable. If no adapter cable is available for your
vehicle, connect the radio as described  (see
separate installation card).

PREPARATION

Vo l t ag e   a n d   p o l a r i t y :   T h e   s e t   mu s t   b e
connected to a 12V car battery with negative
terminal to earth (car chassis). Installation in
vehicles not fulfilling these requirements could
result in malfunction, damage or fire.

CONNECTOR A (fig.2)
Power supply connections
• A7 : Connect to a permanent  12V supply.

This is the main power supply. Ensure this
connection can handle a current of 10A.

• A4 : Connect to a switched 12Vsupply

(switched on/off by car ignition).

• A8: Connect to earth (car chassis).
This connection set up will enable you to make
full use of the ON/OFF LOGIC function of this set
limiting the use of the set to 1 hour after removal
of the ignition key. If this feature does not appear
to be functioning as expected you may require
an adaptor cable.

Optional connections: (fig. 2)
• SDVC (Speed Dependant Volume Control):

Intelligent volume control which automatically
adjust the volume depending on your car's
speed.

- C o n n e c t   p i n   A 1   t o   a   s i g n a l   f r o m   t h e

speedometer of your car. Some cars are
already prepared for it , please consult your
dealer.

- To activate the SMART volume function, see

SPECIAL FUNCTIONS, page 11.

• Electronic antenna/Motorised antenna

:

Connect pin A5 to the power supply for an
electronic antenna or the control wire for the
relay of an automatic motorised antenna.

Do not use this connection for the supply
lead of the aerial motor!

CONNECTOR B (fig.3)
Loudspeakers (use 4 ohm loudspeakers
only)
• Do not connect any of the loudspeaker leads

to earth or directly to a booster/amplifier without
high level input or via an external fader! You
can connect the loudspeaker leads directly to
an amplifier with high level input.

• Connecting 4 loudspeakers (see separate

installation card).

Содержание CD 4506 -



















Отзывы: