manualshive.com logo in svg

VCS VideoJet 10, Руководство пользователя

Поделиться
Скачать
VCS VideoJet 10 Скачать руководство пользователя страница 53

Operation

55

VideoJet 10

Hardware connections
between VideoJet Units

A VideoJet 10 with connected camera as a transmitter and a Video-
Jet 10 with connected monitor as a receiver can be linked simply 
together over an Ethernet network. It is thus possible to link large 
distances with little installation or cabling effort.

Installation

With the appropriate configuration the VideoJet 10 units can auto-
matically establish a connection with each other. This assumes 
that, as a minimum, they are linked into a closed network. To install 
the units proceed as follows:

"

Connect the units using Ethernet cables into the closed network.

"

Connect power to the units.

Connection setup

It is possible to configure the connection using either Terminal soft-
ware or by appropriate configuration via the alarm input. After a 
brief pause, the live image from the camera will be displayed on the 
connected monitor.

Note

Make sure the units are configured for the characteristics of the net-
work environment and that the transmitting unit, under the parame-
ter 

Live video receiver IP address,

 is set for the IP address of the 

receiver (page 

Alarm connections

).

Note

It is only possible to establish the connection using the alarm input 
if the parameter 

Connect on alarm

 is set to 

On

 on the configuration 

page 

Alarm connections 

(see page 36).

Содержание VideoJet 10







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды