background image

Turn on the power at fuse or circuit box.

 

 

Turn off the power at fuse or circuit box

Installation Steps

The Position of Control Panel

Page 2 / 5

1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.

2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the

    preinstalled fixture mounting screws if necessary.

    

Note: Make sure that the fixture mounting screws are lined up horizontally to make the fixture level.

3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: 

     • Connect the hot wire (black insulation) from the fixture to the black wire from the power source.

     • Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. 

     • Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw, then 

       depending on local code, connect it to the house ground wire with the wire connector (C).

     Carefully put all of the wires back into the outlet box.

4. Attach the backplate of the fixture to the  mounting plate unit (A) by inserting fixture mounting screws into set holes 

    on the backplate, then secure it with two rubber pads (E) and two bolt nuts (D).

    

Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall

    surface to prevent water from seeping into the outlet box.

5. Install the bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed.

Fig.1

Sensor

Fig.3

Sensor

Fig.2

Time

Mode

Sens

Test

PC

Auto

Off

Step 1: Rotate the sensor clockwise or counter-clockwise

            at maximum 90 degree to access the adjustable

            knobs. (See Fig.1)

Step 2: Adjust time and sensitivity, choose the mode you 

            want by turning the knob. (See Fig.2 and Fig.A).

Step 3: Restore the sensor to original position by rotating 

            to the opposite direction. (See Fig.3)

 

 

 

"Time" Knob

"Mode" Knob

"Sens" Knob

Fig.A

Time

Mode

Sens

Test

PC

Auto

Off

View Fig.A

Adjustable 

Knob

231012

Содержание T0728
















Отзывы: