Page 4 / 5
221102
Customization Options:
Shut-off Delay
● The shut-off delay is the length of time the light will stay at
brightness after motion is detected.
● You can set the shut-off delay by rotating the Time knob arrow
so it points to the desired time setting
(
30s/1min/3min
). To increase the shut-off delay, turn the knob
clockwise. To decrease the shut-off delay, turn the knob
counterclockwise.
Notes:
1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best
performance, gently clean the lens with a soft cloth every 1 or 2 months to ensure maximum sensitivity.
2. For best performance, install fixture at least 8 feet above the ground. At such a height, the fixture will provide a
detection distance of up to 85 feet at 77 degrees Fahrenheit. (See Fig.7)
3. The sensor detects movement across a detection range of 240 degrees. (See Fig.8)
Fig. 7
Fig.8
10'
8.0'
12.0'
85'
Where you install your fixture is important:
Be sure the light is mounted straight on the wall
or eave; otherwise, the detection distance may
be limited.
4. 3 HOURS (3H) MODE (nighttime operation only)
● In “3H” mode, the light turns to high-level brightness (100%) at dusk, and stays on for 3 hours, then it turns to
low-level 30% brightness. It turns to high-level brightness (100%) when motion is detected, and stays on as long as
motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you
set (30s/1min/3min), then returns to the low level brightness and pre-selected CCT color automatically.
● The light turns off automatically at dawn.
Note: You can adjust the CCT color (2700K~5000K) by using the CCT color (2700K~5000K) knob on the
backplate (See Fig.6)
5. CUSTOM SETTING MODE (nighttime operation only):
●
In "CUSTOM SETTING" mode, the light turn on at dusk and off at dawn automatically.
●
Instead of "3H", the motion sensor operation can be set to start at a specific time. Turn the wall switch OFF, and
turn it ON twice within 3 seconds. The light will go into motion-sensor operation at the specified time every night.
The light turns off automatically at dawn.
For example, a homeowner wants to have the light stay on high-level brightness from dusk to 8pm, and would like
the light to go into "AUTO” motion sensor mode. To achieve this, the homeowner will turn the wall switch OFF,
and turn it ON twice within 3 seconds. This sets the time the light goes into "AUTO" mode every day, the light
will behave the same way.
To revert back to Default, turn the wall switch OFF and then turn it ON after 5 seconds.
Note: You can adjust the CCT color (2700K~5000K) by using the CCT color (2700K~5000K) knob on the
backplate (See Fig.6)
6. Manual Override (nighttime operation only)
● To temporarily override the settings in
“AUTO” or “3H” mode
for on-demand continuous high-level brightness at night, turn
the wall switch “OFF” then turn it “ON” twice within 3 seconds,
the light remains on all night long. To shift back to “AUTO” or
“3H” mode, turn the wall switch “OFF” then turn it “ON” twice
within 3 seconds again. (See Fig.7)
● The light turns off automatically at dawn.
Note: To make sure the above functions operate properly,
always keep the wall switch in the “ON” position (including
the daytime).
Fig. 7
“AUTO” or
“3H” Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
Turn wall switch OFF-ON-OFF-ON
in 0.5~3 Seconds
240˚
