background image

T0099 / T0100---- --- Page 3 / 5

Adjustment Sensor Lower For Short Coverage

Adjustment Sensor Higher For Long Coverage

Fig. 5

1. Gently grasp the light heads and move them up or down, left or 

     right to adjust the light coverage area. Keep the light heads at 

     least 1” (25mm) away from the sensor.(See Fig. 5)

2. 

Keep the light heads 30˚ below horizontal to avoid water 

    damage and electrical shock.

Fig. 3

Fig. 4

Adjusting the Light Head: 

Fig. 6

Fig. 7

Mode

Sensitivity

Delay Time

Low Level Brightness

Sensitivity of Motion Sensor 

        You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side 

        of the bottom surface of the 

sensor. (See Fig. 6)

        Adjust motion sensor sensitivity to HIGH (H), MEDIUM (M), or LOW (L) to achieve desired performance.

        Approximate range for each setting: 20 ft. (L), 45 ft. (M), 70 ft. (H).

Function and Operation

Note: When power is first applied, the light will turn on to 100% brightness. The sensor will take 30 seconds 

to warm up.

   

1. 

AUTO MODE (nighttime operation only) 

           After expiration of the warm-up period, the light will enter a 

           5-minute TEST mode (day  and night operation) and be on 

           at low-level brightness (0-50%).  The light will turn to high-

           level brightness (100%) when motion is detected. It will then 

           revert to low-level brightness about  5 seconds after motion 

           is no longer detected. 

           After expiration of the TEST mode, the light will automatically 

           enter AUTO mode and be on at low-level brightness (0-50%).  

           The light will turn to high-level brightness (100%) when 

           motion is detected. When the motion stops, the light  will then 

           revert to low-level brightness after the shut-off delay time you 

           set  ( 5 ~ 180  seconds).

           The light will turn off automatically at dawn.

    Note: You can adjust the low level brightness (0~50%) by using 

               the low level brightness knob. (See Fig. 7)

2. 3 HOURS (3H) MODE (nighttime operation only)

           The light will turn to high-level brightness (100%) at dusk, and 

           will stay "ON" for 3 hours. The light will then turn to low-level 

           brightness. The light will turn to high-level brightness (100%) 

           when motion is detected, and will stay on as long as motion 

           continues. 

When motion is no longer detected, the lights will 

           remain on for the predetermined shut-off delay time you set (5~180 seconds), and then turn to the 

           predetermined 

low-level brightness automatically.

           The light will turn off automatically at dawn.

   Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 7)

 

140919

Содержание T0099






Отзывы: