Vax V-027CC Скачать руководство пользователя страница 10

Страница: 10 / 12

www.vax.co.uk

operation/ maintenance

Emptying the dirty water tank

Return dirty water tank to the base of the cleaner by
tipping the nozzle down into the basin and dropping it
into place (Fig.4/14).

Lift the front of the cleaner base off the carpeting with
one hand. Line up the black tabs with the grooves of the
front nozzle.

Lift the front nozzle upwards towards the cleaner and
press under the latch until it locks into place (Fig.4/15).

5. Maintenance

Remove dirty water tank and front nozzle put them to
one side (Fig.5/1).

Use a Phillips screwdriver to remove two (2) screws
(Fig.5/2).

NOTE: Phillips screwdriver required

Remove the belt cover. Remove the broken belt (Fig.5/3).

Belt or brush removal and replacement (Fig.5/4)

1. Loop the belt around the rear shaft.

2. Loop the top of the belt above the small pulley and

the bottom of the belt around the lower small pulley.

3. Feed the entire belt over the first large pulley.

4. Loop the belt around the front large pulley and rotate

the front brushbar forward until the belt is in place.

Fig.5/1

Fig.5/2

Fig.5/3

Fig.4/14

Fig.4/15

Содержание V-027CC












