Vauth-Sagel Flat move Скачать руководство пользователя страница 3

3

1.

GENERAL EXPLANATIONS

1.1

Introduction

This TV lift system has been constructed in accordance with the current valid German and European norms, regulations and
guidelines and therefore corresponds with the generally approved technological rules at the time of delivery.

1.2

Intended Use

The TV lift system may only be used for lifting and lowering flat screens with suitable fastening threads and the original system
components in accordance with the operating and assembly instructions and is intended for installation in furniture.

1.3

Safety Information

Read the operating and assembly instructions fully in order to avoid damages caused by incorrect operation or failure to 
observe the operating and assembly instructions.

Keep the operating and assembly instructions in a safe place throughout the lifespan of the product.

Please pass the operating and assembly instructions to future owners or users.

The general requirements for safe design must be observed when installing the TV lift system in a piece of furniture. In case
of any doubt, the respective technical rules and norms must be used (e.g. DIN EN 14749). 

A minimum clearance of 25mm must be provided between the TV and the opening in the furniture.

Observe the minimum clearances, safety information, fixing and ventilation regulations in the operating manual provided by 
the TV manufacturer.

Pay attention to the correct laying of cables => no crushing, shearing or buckling (the travel path must be considered).

The mains plug must be accessible in order to be able to be disconnected in case of any danger.

Attention must be paid to the even distribution of the load when installing the TV. Off-centre loads can lead to damages to 
the system. 

Disconnect the mains plug from the socket before checking, repairing or cleaning the system. 

Check the system for visible damages at regular intervals (e.g. breaks in the cable, splits in the housing etc).

The system may not be operated if there are any damages. 

Overloading the system should be avoided – refer to the maximum load in section 9.

Only allow repairs to be performed by an authorised specialist.

Only original parts may be used.

The system is only intended for use in interior areas.

Protect the system against moisture.

This system is not intended for use by persons (including children) with limited physical, sensory or mental capabilities 
and/or a lack of knowledge unless they are supervised by a person who is responsible for their safety or have received 
instructions from them on how the system is to be used.

Children should be supervised to ensure that they do not play with the system. 

Only operate the TV lift system using the remote control if the movements of the system are in sight.

Содержание Flat move












Отзывы: