background image

 

POWX0481 

EN

 

Copyright © 2019 VARO 

P a g e

 | 

5

 

www.varo.com 

 

Take special care when sanding lead based paint: 

 All persons entering the work area must wear a mask specially designed for protection 

against lead paint dust and fumes. 

 Children and pregnant women must not enter the work area. 

 Do not eat, drink or smoke in the work area. 

 

Do not leave the tool running. Operate the tool only when hand-held. 

 

Ventilate your work area adequately when you perform sanding operations. 

 

Be sure that there are no cracks or breakage on the pad before use. Cracks or breakage 
may cause a personal injury. 

OPERATING INSTRUCTIONS 

Before attempting to use your sander be sure to familiarize yourself with all its operating 
features and safety requirements. 

Warning!  The  sander  should  always  be  disconnected  from  the  power 
supply when assembling parts, marking adjustments, cleaning or when the 
tool  is  not  in  use.  Disconnecting  the  tool  will  prevent  accidental  starting 
that could cause serious injury. 

Do  not  sand  plaster  surfaces,  (WARNING:  In  this  case  your  guarantee 
becomes void) this may clog the motor (brushes, ball bearings, ..). 

7.1 

Sanding 

 

Hold the sander in front and away from you, keeping it clear of the work piece. 

 

Start the sander 

 

Let the motor build up to speed then gradually lower it on to the work with a slight forward 
movement . 

 

Move the sander slowly over the work piece using forward and back or side to side 
strokes. 

 

Upon completion of the sanding operation remove the sander from the work piece before 
turning if off. 

7.2 

Switching On-off 

Connect the plug to the power supply. 

 

Switch the power tool on: push the ON/OFF switch button (1

) forwards onto the “

I

” 

position. 

 

Switch the power tool off: pull the ON/OFF switch button backwards to the “

O

” position.   

WARNING: Never use the machine for sanding magnesium work piece. 

7.3 

Backing Pad accessory Installation 

The sanding plate is equipped with a hook and loop rubber backing pad. This uses hook and 
loop backed accessories, which firmly grip the backing pad when applied with moderate 
pressure. 
To change, merely peel off the old accessory, remove dust from the backing pad if necessary 
and press the new accessory in place. Be sure to align the sanding sheet holes with the holes 
in the backing pad as best you can to allow the dust extraction system to function effectively. 
After considerable use the backing pad surface will become worn, and must be replaced when 
it no longer offers a firm grip. If the backing pad facing is wearing prematurely, decrease the 
amount of pressure applied during the operation of the tool. Damage to the pad is not covered 
the warranty. 

Содержание PowerPlus POWX0481









Отзывы: