background image

 

POWX00425 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

7

 

www.varo.com 

7.5 

Forward/reverse selector (right/left rotation selector) (4) 

The drill has a forward/reverse selector located above the switch trigger. 

 

F(Forward) (Forward): Press selector on right side of machine (to the left  side): drill turns 
right (forward, fasten screws) 

 

R(Reverse) (Reverse): Press selector on left side of machine (to the right  side): drill turns 
left (reverse/ loosen screws) 

CAUTION:  To  prevent  damage  to  the  gearbox,  always  allow  the  chuck  to 
come  to  a  complete  stop  before  changing  the  direction  of  rotation  or 
selecting another speed (HI-LO). To stop, release the trigger switch. 

7.6 

Speed selector (3) 

Your cordless drill has a two-speed gear, designed for drilling or driving at LO or HI speed. A 
slide switch is located on top of your drill to select either LO (1) or HI (2) speed. 
The low speed (LO) is used, in combination with the torque setting, for screwing screws in or 
out and for drilling with a larger diameter. 
The high speed (HI) is used only for drilling (never for screwing, as this may lead to damage of 
the tool). 

7.7 

LED worklight (6) 

Your cordless drill is equipped with an LED light at the front (above the ON/OFF switch) above 
the  battery  pack.  The  white  LED  light  will  light  when  you  operate  the  machine,  providing  the 
work area to be lighted. 

7.8 

TPR soft grip 

 

Your cordless drill is equipped with TPR soft grip and protective parts.  TPR 
(Thermoplastic rubber) is elastic, chock absorbing and environmental friendly (recyclable). 

8  (PRE)OPERATION 

8.1 

Battery charging 

Use only the battery charger supplied with your tool. Only these battery chargers are matched 
to the lithium ion battery of your power tool. 

Note:  The  battery  is  supplied  partially  charged.  To  ensure  full  capacity  of 
the  battery,  completely  charge  the  battery  in  the  battery  charger  before 
using  your  power  tool  for  the  first  time.  The  lithium  ion  battery  can  be 
charged  at  any  time  without  reducing  its  service  life.  Interrupting  the 
charging procedure does not damage the battery. 

 

Connect the plug of the charger to the loading socket (10) of the battery set. 

 

Red LED light will lid once the battery has been connected to the charger and the charging 
procedure will proceed. 

 

The battery set is completely loaded and ready for use once the green LED is lit the red 
LED if off -after approximately 3-5 hours. 

8.2 

Battery capacity indicator 

There are battery capacity indicators on the battery pack, you can check the capacity status of 
the battery if you squeeze the button (7). 
Those 3 LED might show the status of the capacity level of the battery: 
3 LED’s are litt: Battery fully charged 

LED’s are litt: Battery 60% charged 

1 LED is litt: Battery almost discharged 

Содержание POWERPLUS POWX00425













Отзывы: