background image

 

POWE40040 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

5

 

www.varo.com 

 

Keep the cord well clear of the working area. 

 

Sanding certain substances can produce harmful dust. Use respiratory protection 
equipment and safety goggles. 

 

Never sand surfaces painted with lead based paint. 

 

Do not lay the sander on its side before it has completely stopped. 

 

Immediately switch the machine off if it becomes jammed. 

 

Asbestos-containing materials may not be worked on! 

 

Touching or breathing in of the dust particles constitute a hazard for the machine operator 
and other persons in the vicinity. 

7  ASSEMBLY 

Do not sand plaster surfaces, (WARNING: In this case your guarantee 
becomes void) this may clog the motor (brushes, ball bearings,...). 

Remove the power tool from the packaging. Do not plug it into the electrical grid before 
assembly. 

7.1 

Grinding Belt Selection 

Type K# for work on wood, iron and steel work pieces. 

Belt Grain 

Use 

K 40 

Rough machining 

K 60 

 

K 80 

Medium, rough machining 

K 100 

 

K 120 

 

K 150 

Fine machining 

K 180 

 

K 240 

 

For rough grinding, please use a belt with a belt grain size of 40# and 60#. For finer grinding, 
use one of the corresponding finer grain sizes. On uneven surfaces, first use a rough grinding 
belt for smoothing and then a finer belt for the fine work. 

7.2 

Replacing the Sand Belt Fig. 1-2-3) 

Disconnect the sander from the mains. 
Pull out the locking lever in the side of the belt sander to loosen the sand belt (16) from the 
rollers. Select a sanding belt with the appropriate grain size for the task.  
Fit the sand belt onto the rollers. 
The arrows on the sand belt must follow the direction of rotation. 
Lock the sanding belt in place using the locking lever (5). 
Switch on the sander and check that the sand belt runs continuously in the centre of the rollers. 
If it does not, use the adjusting screw (15) to adjust the position of the sand belt. 

8  USE 

8.1 

Installing the Dust collection bag (Fig. 4) 

Attach the dust collection bag (1) with the help of the wire frame to the opening on the dust 
discharge outlet of the machine. When the dust bag is too full, it affects the suction power. 
Therefore, it is advisable to empty the bag as soon as it is 2/3 full. To empty, open the catch 
on the bottom side of the dust collection bag. 

 

 

Содержание POWERPLUS POWE40040










Отзывы: