POW63771
EN
Copyright © 2016 VARO
P a g e
|
13
www.varo.com
10.3
Blade mounting torque
Center Bolt 40Nm.min, 54Nm.max. To insure safe operation of your unit. ALL nuts and bolts
must be checked periodically for correct tightness.
After prolonged use, especially in sandy soil conditions, the blade will become worn and lose
some of the original shape. Cutting efficiently will be reduced and the blade should be
replaced. Replace with an approved factory replacement blade only. Possible damage
resulting from blade unbalance condition is not the responsibility of the manufacturer.
When you change the blade, you must use the original type marked on the blade (for order the
balde, pls. contact your local dealer or call our company, see cover page).
Warning: Do not touch rotating blade.
11 TROUBLESHOOTING
Problem
Probable cause
Corrective action
Engine does not
start.
Throttle chock not in the correct
position for the prevailing
conditions.
Move throttle chock to correct
position.
Fuel tank is empty.
Fill tank with fuel.
Air cleaner element is dirty.
Clean air cleaner element.
Spark plug loose.
Tighten spark plug to 25-30 Nm.
Spark plug wire loose or
disconnected from plug.
Install spark plug wire on spark
plug.
Spark plug gap is incorrect.
Set gap between electrodes at 0.7
to 0.8 mm.
Spark plug is defective.
Install new, correctly gapped plug.
Carburetor is flooded with fuel.
Remove air cleaner element and
pull starter rope continuously until
carburetor clears itself and install
air cleaner element.
Faulty ignition module..
Contact the service agent.
Engine difficult to
start or loses
power.
Dirt, water, or stale fuel tank.
Drain fuel and clean tank. Fill tank
with clean, fresh fuel.
Vent hole in fuel tank cap is
plugged.
Clean or replace fuel tank cap.
Air cleaner element is dirty.
Clean air cleaner element.
Engine operates
erratically.
Spark plug is defective.
Install new, correctly gapped plug.
Spark plug gap is incorrect.
Set gap between electrodes at 0.7
to 0.8 mm.
Air cleaner element is dirty.
Clean air cleaner element.
Engine idles
poorly.
Air cleaner element is dirty.
Clean air cleaner element.
Air slots in engine shroud are
blocked.
Remove debris from shots.
Cooling fins and air passages
under engine blower housing are
blocked.
Remove debris from cooling fins
and air passages.
Engine idles
poorly.
Gap between electrodes of spark
plug is too close.
Set gap between electrodes at 0.7
to 0.8 mm.
Net Weight
(with grass
collector)
25Kg
28Kg
28Kg
28.5Kg 31.5Kg 31.5Kg
22.5Kg
Height
adjstment :
Level
1
Level
2
Level
6
Level
9
25 mm 25 mm 25 mm 25 mm 25 mm 25 mm
25
mm
30.5mm 30.5mm 30.5mm 30.5mm 30.5mm 30.5mm
36.25
mm
36.1mm 36.1mm 36.1mm 36.1mm 36.1mm 36.1mm
47.5m
m
41.7mm 41.7mm 41.7mm 41.7mm 41.7mm 41.7mm
58.75
mm
47.2mm 47.2mm 47.2mm 47.2mm 47.2mm 47.2mm 70mm
52.8mm 52.8mm 52.8mm 52.8mm 52.8mm 52.8mm
/
58.3mm 58.3mm 58.3mm 58.3mm 58.3mm 58.3mm
/
63.9mm 63.9mm 63.9mm 63.9mm 63.9mm 63.9mm
/
69.5mm 69.5mm 69.5mm 69.5mm 69.5mm 69.5mm
/
75mm 75mm 75mm 75mm 75mm 75mm
/
Level
3
Level
4
Level
5
Level
7
Level
8
