Varimixer AR30 VL-1S Скачать руководство пользователя страница 10

Страница: 10 / 20

Adjustments of speed (low and high speed cam disks):

Prior to any adjustment the, the bowl must be in its top position and the safety guard must be closed.

Switch off the power to the mixer, this must be done via the emergency stop. Remove the lid of the mixer.

Dismantle shaft for speed regulation: The arm

(B)

is released from the servo motor shaft by removing the cotter pin

(C)

and the pin

(D)

. The arm

(B)

must not be loosened from the shaft

(E)

Loosen the screw

(F)

and take out the speed indicator

(G).

Loosen the screw in the speed indicator clamp

(H)

and remove the disk with arrow

(I)

The manual speed selector handle

(J)

is placed in the shaft

(E)

so that it points upwards and forwards.

Release the emergency stop and start the mixer.

Turn the handle for manual adjusting of speed to minimum speed until the distance from the v-belt to the edge of the

planetary head pulley is approximately 1 mm. see

fig. 7a.

Stop the mixer by pressing emergency stop.

Loosen the two screws on the two cam disks

(K)

and

(L).

Turn the cam disk for minimum speed

(K)

until it is activating the micro switch. Tighten the screw.

Release the emergency stop and start the mixer.

Turn the handle for manual adjusting of speed to maximum speed until the distance from the v-belt to the edge of the

motor pulley is approximately 3 mm.

see fig. 7b.

Stop the mixer by pressing emergency stop.

Turn the cam disk for maximum speed

(L)

until it is activating the micro switch. Tighten the screw.

Remove the manual speed selector handle

Remount the servo motor shaft on the arm

(B)

. It is urgent to make sure that the servo motor is not clamped against the

machine column, the shaft

(E)

or other parts of the mixer, and that the “bad position”

(Fig. 8)

for the motor is avoided.

If the servomotor is not positioned correctly (according to the description above), the two screws

(M)

and

(N)

that fix

ates the arm on the shaft are loosened and the arm adjusted. Now the handle for manual speed adjustment has to be

mounted again and the cam discs must be adjusted once again.

When the min. and max. speed has been adjusted correctly, the speed indicator clamp, the disk with arrow and the

speed indicator are remounted.

Cam disks for minimum and maximum speed have now been adjusted.

Содержание AR30 VL-1S





















Результаты поиска

Содержание AR30 VL-1S

Отзывы:

Похожие инструкции для AR30 VL-1S

Бренды по названию

Популярные бренды

Varimixer AR30 VL-1S, Руководство по эксплуатации

Результаты поиска

Содержание AR30 VL-1S

Отзывы:

Похожие инструкции для AR30 VL-1S

Бренды по названию

Популярные бренды