manualshive.com logo in svg

Varian VHS-10, Инструкция по эксплуатации

Поделиться
Скачать
Varian VHS-10 Скачать руководство пользователя страница 4

i

OPERATION AND MAINTENANCE OF THIS EQUIPMENT INVOLVES SERIOUS RISK. IT IS THE
RESPONSIBILITY OF THE USER TO MAINTAIN SAFE OPERATING CONDITIONS AT ALL TIMES.
VARIAN  ASSUMES  NO  LIABILITY  FOR  PERSONAL  INJURY  OR  DAMAGE  RESULTING  FROM
OPERATION OR SERVICE OF THE EQUIPMENT.

Carelessly or improperly operated equipment can cause serious injury or death and/or damage to the
equipment. The  emergency  and  safety  procedures  in  this  manual  are  provided  to  help  users  and
qualified  persons  to  operate  and  service  the  unit  safely. Recommendations  are  believed  to  reflect
accepted industry practices in effect on the date of publication of this manual. Special applications
must be reviewed and approved by an industrial hygienist or chemical safety engineer.

Varian  has  no  control  over  the  use  of  this  equipment  and  is  not  responsible  for  personal  injury  or
damage  resulting  from  its  use. The  safe  use  and  disposal  of  hazardous  or  potentially  hazardous
materials of any kind is the sole responsibility of the user. Observe all WARNINGS and CAUTIONS
to minimize the serious hazards involved.

It is the sole responsibility of users of Varian equipment to comply with all local, state, and federal safety
requirements  (laws  and  regulations)  applicable  to  their  system. Employ  the  services  of  an  industrial
hygienist and/or a qualified chemical safety engineer in order to ensure safe installation and use.

This instruction manual contains information which will assist qualified operators in the operation, and
qualified service engineers to carry out field-servicing the Varian equipment.

Содержание VHS-10





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды