CB-800
CB-1000
2.7 M
AINTENANCE
, C
ARE
, S
TORAGE
Before each use of the machine, check the tightness of its bolted connections. Replace the lost screwed
connections with the original parts that are designed for the given spot. Use of non-original parts of poor quality
will expose you to risk of injury or damage to the machine!
Owing to the weight of the machine, all the maintenance and adjustment shall be performed by two people.
•
To secure a long-term satisfaction with our product, it is necessary to provide it with due care and maintenance. By providing regular
maintenance you will prevent its rapid wear and you will secure correct operation of all its parts.
•
Observe all instructions concerning maintenance and adjusting intervals. We recommend that you keep records of operating hours and
the conditions under which the machine is used (these may be useful for servicing centres). We recommend that you have the post-season
maintenance implemented by one of our authorized service centres; the same applies to standard maintenance if you are not certain of
your technical capabilities.
The good help to monitor operating hours is the
VARI PowerMeter
device. This accessories can be bought with every dealer
of VARI products.
Due to the high proportion of BIO components in the fuels, we strongly recommend that you drain all the fuel from the
carburettor before each shutdown of the machine - close the fuel valve and let the engine run until it switches off
spontaneously.
2.7.1 R
ECOMMENDED
T
OOLS
AND
A
CCESSORIES
For the assembling and maintenance of your machine, we recommend the following tools and accessories
Fig. 38
.
TOOLS
ACCESSORIES
Spanner No. 10 mm - 2x
Petrol can, capacity 5 litres - Ord. No. 3562
Side eyelet wrench curved No. 15 mm - 1x
HONDA fuel stabiliser - Ord. No. 08CXZ-FSC-250
Curved ratchet 3/8“ + socket 15 mm + extension - 1x
Briggs & Stratton Fuel Fit™ fuel stabiliser - Ord. No. 992381
Spark plug wrench 21 mm - 1x
Hour meter VARI POWERMETER - Ord. No. 4227
Flat screwdriver
Table 18: Recommended Tools and Accessories
2.7.2 S
ERVICING
INTERVALS
Activity
Prior to every use During the season
Before prolonged storage
Checking engine oil level
Yes
Per the engine operating instructions
We recommend changing the oil fill
Engine air filter cleaning
Check
Every 10 hours
Yes
Tyre pressure check
Yes
As needed
Yes, inflate to the maximum pressure
Washing
As needed
As needed
Yes
Checking tightening of screwed connections
Yes
Every 5 hours
Yes
Oil in the brush drive gearbox
-
After the first 5 hours, then after every
100 hours
We recommend changing the oil fill
Check of the condition and tension of the V-belts -
After the first 5 hours, then after every
20 hours
Yes
Table 19: Servicing intervals
2.7.3 M
ACHINE
L
UBRICATION
When working with lubricants, observe the basic hygiene regulations and observe the environmental protection
regulations and laws.
For trouble-free and easy movement of all mechanical parts, pay sufficient attention to lubrication.
2.7.3.1 E
NGINE
O
IL
C
HANGE
If you are not sufficiently manually skilled, have the operations done by an authorised service centre.
•
Follow the engine operating instructions for the type, quantity, and method of engine oil changing.
•
When draining oil out of the engine, tilt the machine to the side where the oil spout is fitted or disassemble the entire engine, including
the engine plate.
•
Standard interval
of oil change, specified by the engine manufacturer,
reduce it by half
. Dirt sweeping always generates a big
amount of dust particles.
61
The tools and accessories are not included in the delivery of the machine, they must be purchased separately.
62
In the event of a very dusty environment, the check and cleaning should be done every hour!
34
re
vi
ze
1
2/
20
21
