Vantage Hearth DMX-DALI-GW, Руководство по установке

Страница: 2 / 6

I N S T A L L A T I O N
©Vantage, 8/1/2016 / IS-00703-C Vantage DMX DALI Gateway – MODEL: DMX-DALI-GW page 2 of 6
CLICK ►
FIGURE 1
◄ CLICK
CLICK ►
◄ CLICK
Check Box ►
FOR SLAVE MODE
Enter the InFusion
Controller’s IP Address
►
Recommend: Leave at default.
See step xi. - a. above.
►
b
Section
Always change both DMX and DALI buses
to
Slave or Master mode together.
FIGURE 2
iii. Connect the computer directly to the DMX-DALI-
GATEWAY; the DDG station must be powered.
iv. Modify the computer’s network adapter settings to
have a static IP address of 192.168.1.5.
v. Type http://192.168.1.225/config.html in a browser
to start the DGM Configuration interface tool. ( TIP: If
unable to connect, try the other default IP address
192.168.1.4 or perform a factory reset to the station
and try both IP addresses again.
)
vi. Click the Ethernet TCP/IP Settings button (image
below).
vii. Change the Static IP to the reserved address in step i .
above and set NetMask and Gateway as needed.
viii. Record the IP Address assigned to the DDG device
for later use in Design Center.
ix. Return to the DGM Config home page by clicking on
the Vantage icon.
x. If using the DDG station in Slave Mode continue to
step xi. Otherwise, skip to step xiv .
xi. For Slave Mode change the Ethernet UDP & Artnet
settings by clicking on the Ethernet UDP & Artnet
button as shown below.

Check Enable TX on port: 1026

In the tx ipv4 addr: field, enter the InFusion
controller’s IP address.

It is recommended to leave the min/max scan
time at default:
a. min. 25ms -
b. max. - ) (blank ).
c. Set the tx scan time in ms (milliseconds) for
min. to seconds for max. Load feedback is
sent within these intervals
when there is no
traffic.
d. To disable feedback when there is no traffic,
leave the min. and max. fields blank.
xii. Click on the Vantage icon to return to the DGM
Config home page.
xiii. Select Bus 2 and change to Slave mode, exit back to
home page and save. Repeat for Bus 3 – see figure 2.
xiv. Click on Save & Reboot to commit the changes.
xv. Disconnect the computer from the DDG station.
xvi. Remember to reset the computer’s network adapter
and reconnect to the local network. Connect the DDG
station to network.
b. If your network is on the 192.168.1 subnet:
i. Power up and connect the DMX-DALI-GATEWAY to
the network.
ii. On your router, make sure to set up a reserved/static
address for the device. The default address of
192.168.1.225 may be used if available on local network.
To Change IP Address :
iii. Type http://192.168.1.225/config.html in a browser
to start the DGM Configuration interface tool.
iv. Click the Ethernet TCP/IP Settings button. See Figure
1 , in step a, previous column.
v. Change the Static IP to a desired address on the same
subnet as the controller.
vi. Record the IP Address assigned to the DDG device so
this may be added in Design Center.
vii. Return to the DGM Config home page, click on
the Vantage icon. (Also see Master or Slave
Mode of Operation , below).
viii. If using the DDG station in Slave Mode see step xi. to
xiii. in section a , otherwise skip to step ix. in this
section, section b .
ix. Click on Save & Reboot to commit the changes.
Master
or Slave Mode of Operation
The DDG station ships with all buses in Master Mode by default.
To place the DMX and DALI buses in Slave Mode type
http://192.168.1.225/config.html or current IP address, in a
browser. See, DMX-DALI-GATEWAY / DGM Configuration
Steps (pg1). Always change both buses to the same mode.*
Master Mode Operation: In Master Mode the InFusion system
controller is the master controller for all connected DMX
and/or DALI systems. The DDG is the managing gateway
for information between the InFusion controller and
connected DMX and/or DALI buses in real time.
Slave Mode Operation: In Slave Mode the InFusion controller
uses the DDG to monitor information - no Design Center
control - from the DMX and/or DALI buses. Note:
Feedback information may be used to trigger Design
Center tasks. See
DMX-DALI-GATEWAY / DGM
Configuration Steps page 1 & 2 if using Slave Mode .
*IMPORTANT: Using the DGM Configuration tool, it is possible
to independently place each bus, DMX and DALI, in Master
or Slave mode, however, Vantage does not support mixed
Master/Slave configurations. When changing either bus to
Master or Slave mode,
always change both buses to the
same mode. Remember to click the Save &
Reboot button when changing any settings in the
DGM Configuration tool.
Installation