Vanguard 7300 Series Скачать руководство пользователя страница 166

Страница: 166 / 227

5-28

Modifying Your Vanguard 7300

Removing and Replacing the T3/E3 ATM Card and Rear Transition Module

Removing and Replacing the T3/E3 ATM Card

Introduction

This section explains how to remove and reinstall the T3/E3 ATM Card.

Note

Be sure to review all applicable warnings and cautions in the “General Card
Replacement Guidelines” section on page 5-2 before you begin.

Removing the T3/
E3 ATM Card

Use the steps in this table to remove the T3/E3 ATM Card from the Vanguard 7300
enclosure:

Installing the T3/E3
ATM Card

Use the steps in this table to install the T3/E3 ATM Card into the Vanguard 7300
enclosure:

Step

Action

Using a screwdriver, loosen the captive screws from the front of the
T3/E3 ATM Card.

To eject the T3/E3 ATM Card, press the two ejector levers outward at the
same time.

Pull the T3/E3 ATM Card from the enclosure.

Place the module on a clean, grounded, and static-free surface.

Caution

Avoid touching areas of integrated circuitry; static discharge can damage
these circuits.

Step

Action

Open the ejector levers on the T3/E3 ATM Card.

Align the T3/E3 ATM Card with the card rails on the Vanguard 7300
chassis.

Carefully insert the T3/E3 ATM Card in the card rails and slide the card
until you feel resistance.

Simultaneously press the ejector levers inward until they lock.

Tighten the captive screws.

Содержание 7300 Series




































































































































































































































Результаты поиска

Содержание 7300 Series

Отзывы:

Похожие инструкции для 7300 Series

Бренды по названию

Популярные бренды

Vanguard 7300 Series, Руководство по установке

Результаты поиска

Содержание 7300 Series

Отзывы:

Похожие инструкции для 7300 Series

Бренды по названию

Популярные бренды