background image

11

IOM-3600

Gasket seating surfaces for tank nozzle flange must be clean, free of scratches, 
corrosion, tool marks and flat. Use either a full faced or ring gasket for steel and 
stainless steel raised face flanges.
FRP and Aluminum vents are furnished with flat faced flanges. It is recommended 
that they be installed on mating flat face flanges with a full faced gasket.  If the flat 
face of the vent is sealing against a raised face steel flange, a spacer or filler ring 
must be used to fill the annular space of the raised face steel flange.
Refer to Gasket Dimension Table.
Ensure that the gasket material is suitable for the service. 

 

Make sure that the 

gasket is compressed evenly and the flanges are not distorted. Utilizing proper 
torquing techniques will ensure a tight seal and prevent leakage around the 
gasket. See preceding page.

NOTE: 

 Incorrect positioning and/or selection of gasket(s) between the flanges 

will cause bending stresses at the flange that may damage the flange joint 
as bolting is tightened. This is more likely to occur with aluminum or cast iron 
materials.

RECOMMENDATIONS FOR PROPER GASKET INSTALLATION

Correct Installation

Correct Installation

Incorrect Installation

Full Faced Gasket

Spacer and
Full Faced Gasket

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be 

construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability.  We reserve the right 

to modify or improve the designs or specifications of such product at any time without notice.

Cashco, Inc. does not assume responsibility for the selection, use or maintenance of any product.  Responsibility for proper selection, use and maintenance of any 

Cashco, Inc. product remains solely with the purchaser.

Содержание 3000 SERIES














Отзывы: