background image

 

11 

6. Allow the ValueLam 4500HC-2 to run a small amount of film before feeding the print into 
the  laminator  to  avoid  a  dwell  line  across  your  print.    Feed  the  print  slowly  and  evenly, 
smoothing it as the rollers pull it through. 
 
7.  You  may  laminate  subsequent  prints  now,  leaving  ample  space  between  each  print  for 
trimming. 
 

   8. Once your last print has completely exited the laminator, turn the MOTOR switch OFF. 
 

9.When you have finished laminating, turn heat switch off and pull out the roller pressure pins     
to release the pressure on the rollers.  This will eliminate the chance of “flat spotting” the 
rollers. 

 

Coating Mount Board... 

 

 
The ValueLam 4500HC-2 is capable of applying an adhesive coating to mount board that has 
not previous been coated.  

 
1. Load a roll of adhesive, with the liner wound to the outside, onto the top mandrel in the 
same manner as with laminating film. 
 
2. Load a roll of paper on the bottom mandrel or use adhesive the same width as the mount 
board to keep the adhesive from accumulating on the rollers. 
 
3.  Set  the  temperature  to  approximately  125°F.  The  ValueLam  4500HC-2  will  take 
approximately 10-15 minutes to reach operating temperature.  The roller temperatures are 
indicated on the LED displays. 
 
4.  Feed  the  uncoated  mount  board  into  the  laminator  behind  a  small  leader  board.    The 
leader board will prevent the compression of the leading edge of your mount board.   
 

   5. You may coat subsequent boards now, one directly behind the other, so that the board in      
   front becomes the leader board. We recommend that you coat a sufficient supply of mount  
   board in one session so you’ll have it ready for future use.

 

 

 
Mounting & Laminating... 

 

1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions 
and the laminating film is loaded correctly. 
 
2. Place mounting pins in proper “mount” holes. 
 
3. Turn the TEMPERATURE CONTROL switch to the ON position.   
 
4. Set the temperatures according to the film manufacturer’s recommendations for the film 
you  have  chosen.    The  ValueLam  4500HC-2  will  take  approximately  10-15  minutes  to 
reach  operating  temperature.  The  temperatures  of  the  heated  rollers  are  indicated  on  the 
LED display. 
 

Содержание 4500HC-2

















Отзывы: