background image

Model

 

780NG

780LPG

Gas

Natural Propane

Altitude (Ft.)*

0-4,500 feet*

Input Maximum (Btu/h)

30,000

28,000

Input Minimum (Btu/h)

6,500

14,500

Manifold Pressure (in w.c.)

4.0

10.5

Minimum Supply Pressure 

(in w.c.)

5.0

11.0

Maximum Supply Pressure 

(in w.c.)

10.0

14.0

Main Burner Injector Marking

850

300

Pilot Injector Marking

51

30

Min. Rate By-Pass Screw

125

125

Burner identi

fi

 cation

L

EGEND

 G4

4002613-03

©2012, Miles Industries Ltd.

Gas Conversion Kit

780NGK/NPK

Installation Instructions

This appliance is certi

fi

 ed for use from 0–4500 feet. For 

altitudes above 4500 feet, see local codes.

Kit Contents

1 Pilot injector
1 Burner
1 Main burner elbow injector
1 Set of conversion labels
1 Set of air shutter
1 Air baf

fl

 e for rear log support (LPG only)

4 Screws (for LPG air baf

fl

 e)

Tools Required

•  Wrenches, to disconnect gas line
•  Phillips (+) screwdriver, to remove burner module
•  Small (jewelers size) 

fl

 at blade screwdriver, to set 

pressure

• Small 

fl

 at blade screwdriver, to release pressure tap 

on valve

•  Nut driver 8 mm or 5/16”, to remove burner nuts
•  Needle nose pliers, to remove by-pass screw
•  Hex (Allen) wrench, 4 mm or 5/32”, to remove pilot 

injector

•  Manometer, to set pressure when regulator is integral 

with valve

Speci

fi

 cations

Use with with 

Valor Models 780 Heaters ONLY

WARNING

This conversion kit shall be installed by a 
quali

fi

 ed service agency in accordance with 

the manufacturer’s instructions and all appli-
cable codes and requirements of the authority 
having jurisdiction. If the information in these 
instructions is not followed exactly, a 

fi

 re, ex-

plosion or production of carbon monoxide may 
result causing property damage, personal in-
jury or loss of life. The quali

fi

 ed service agency 

is responsible for the proper installation of this 
kit. The installation is not proper and complete 
until the operation of the converted appliance 
is checked as speci

fi

 ed in the manufacturer’s 

instructions supplied with the kit.

Use this manual in conjunction with the instal-
lation manual supplied with the appliance.

Содержание Legend G4 Series









Отзывы: