background image

17

Operating Instructions

The controls of the fireplace are located near the top of 

the unit behind a flip down panel / louver.

Plug your electric fireplace.

Flip down the front panel / louver near the top of the 

unit to reveal the controls.

Main ON/OFF Power Switch and LED:

 The main 

ON/OFF switch is located on the left side of the 

control panel. The “|” indicates ON and “O” indicates 

OFF. The Power LED is located at the farthest right 

side of the control panel. It has the word “POWER” 

right below it. 

When the unit is first turned on, the Power LED will 

be Green and the default settings are as follows:

Ember bed: HIGH

Flame: HIGH

Heater: OFF

Temperature Control Button and LED:

 The 

HEATER LED is located to the right of the FLAME 

Button. It has the word “HEATER” right below it. Push 

the TEMP button to cycle through different heater 

settings. Press and release the TEMP button to cycle 

through LO, MED, HI and OFF. Each time the TEMP 

button is pushed, the HEATER LED will change to its 

corresponding colour: Green for LO, Orange for MED, 

Red for HI, and blank for OFF.  

When the heater is turned on, heat will emit through 

the heater vents behind the top panel / louver. 

The heater has a built-in thermostat so it will shut 

off automatically once the preset temperature is 

reached. It will also turn on automatically if the room 

temperature drops below the preset temperature. 

Note:

 When the heater is truned on for the first time, 

it may release a slight, harmless odor. This odor is a 

normal occurrence caused by the initial heating of the 

internal elements and should not occur again.

Flame Control Button:

 This button is located to the 

right of the TEMP Button. After the power is turned 

on, push the FLAME Control Button to adjust the 

flame height and ember bed brightness. Press and 

release the Flame Control Button to cycle through 

LO, MED, HI and OFF.

1.
2.

3.



4.

5.

Heater LED

Temperature

Control Button

Power LED

Flame Control

Button

Remote Control

Receiver

ON/OFF

Power Button

Controls For

Electric Fireplace

RECEIVER

HEATER POWER

TEMP

FLAME

TEMP

FLAME

HEATER POWER

RECEIVER

Содержание DZ1GEC

























Отзывы: