background image

Designed and Manufactured by / for

Miles Industries Ltd.

 190–2255 Dollarton Highway, North Vancouver, BC, CANADA  V7H 3B1

Tel. 604-984-3496  Fax 604-984-0246

www.valorfi replaces.com

© Copyright Miles Industries Ltd., 2017

Set the manifold pressure 

1.  Remove the valve access panel (5 screws) on the 

left hand side of the appliance case. If the appliance 
is already installed, you will need to pull the left 
hand side out of the cavity.

2.  Fit a manometer to the 

manifold pressure test tap 
on the valve—see fi gure 
at right. 

3.  Light the appliance and 

turn the control to full 
input. 

4.  Adjust the pressure 

adjustment screw using 
a small jeweller’s size 
fl at blade screwdriver—
as shown below—while 
the appliance is running 
at full input to produce 
manifold pressure, as per 
Specifi cations table on page 1.

Front Face of Control Valve

Pry off

Plastic Cap

Front Face of 
Control Valve

Pressure
adjustment
screw behind
plastic cap

Increases pressure

Decreases pressure

Manifold Pressure 
Test Tap

Valve Inlet 
Pressure

Loosen screw to check 

(tighten afterwards)

Pressure Test Tappings

5.  Turn off  the appliance, remove the manometer and 

tighten the test tapping screw. Check for leaks.

6.  Complete the required details of label “This 

appliance was converted on... by...” position along 
with the label “This control has been converted...” 
onto the inside face of the controls cover panel.

7.  Refi t and secure the controls cover panel.
8.  Push the fi replace back into the cavity.

Re-install the fuel bed logs

Reinstall the fuel bed in the fireplace following 
instructions in the installation instructions supplied 
with the appliance.

Fit the conversion labels

1.  Complete the required details of label 

“This 

appliance was converted on... by...”

 .

2.  Fit the conversion label with the new specifi cations 

label on the back side of the lighting instructions 
card rolled up at the right of the fi rebox behind the 
side access door.

3.  Fit the label 

”This control has been converted...”

 

inside the control valve access panel on the left side 
of the appliance case near the control valve.

Valve

Controls 
cover

4

Содержание 785KNGK









Отзывы: