Valmar Sweety Quick 60 Скачать руководство пользователя

Страница: 40 / 43

The errors, the causes and troubleshooting:

12.3 REGULAR MAINTENANCE INSPECTION PLAN

All maintenance and servicing must be carried out by technicians authorized by
VALMAR Company.

Error

Cause

Troubbleshooting

Appliance will not start up when
switched on

There is no power supply

Check the power circuit. Turn ON
the safety switch.

Automatic fuses are
disconnected.

Switch on the power fuses again.

Compressor starts, but stops
emediately and display shows
“

- P -

“

Water supply is closed

Open water outlet

Water inlet is disconected Conect water inlet

Heating cycle takes too long

Heater has burnt out.

Call VALMAR service tehnicans.

There is not enough glycol
in the system.

Call VALMAR service tehnicans.

Cooling cycle takes too long

Water supply flow is too
weak.

Make sure that the valve is open
and the pipes are not jammed.

There is not enough glycol
in the system.

Check the quantity of the glycol.

Cooling is inadequate

The expansion valve does
not work properly.

Call VALMAR service tehnicans.

Inadequate condensation. Call VALMAR service tehnicans.

The cooling filter is
blocked.

Call VALMAR service tehnicans.

Gas leckage in the system. Call VALMAR service tehnicans.

Maintenance inspection

WEEKLY MONTHLY EACH THREE

MONTHS

YEARLY

Security systems

Electricity connections

Tightness of the screws and sealing

Door safety switch (DOOR)

Gas

Glycol

Содержание Sweety Quick 60












































Результаты поиска

Содержание Sweety Quick 60

Отзывы:

Похожие инструкции для Sweety Quick 60

Бренды по названию

Популярные бренды

Valmar Sweety Quick 60, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Sweety Quick 60

Отзывы:

Похожие инструкции для Sweety Quick 60

Бренды по названию

Популярные бренды