- 11 -
g
SYMBOLS
Carefully observe the symbols in fig. B and memorise their
respective meanings. Correct interpretation of the symbols
allows safer use of the power tool.
1. Model, technical data
2. Warning!
3. Carefully read all instructions before use.
4. Double electric insulation.
5.
Electric and electronic waste may contain potentially
hazardous substances for the environment and human
health. It should therefore not be disposed of with do-
mestic waste, but by means of differentiated collection
at specific centres or returned to the vendor in the event
of purchasing a new similar tool. The illegal disposal of
waste will result in administrative sanctions.
6. Manufacturing lot number. The first 2 figures of the lot
number indicate the year of manufacture.
7. Certification mark.
V Volt
Hz Hertz
~
alternating current
W Watt
m metres
mm millimetres
s seconds
l litres
kg kilograms
dB decibel
We thank you for having purchased this product that will
hereafter also be referred to as “electric pole chainsaw”.
!
IMPORTANT! The electric pole chainsaw is suitable for
cutting tree branches with the operator on the ground.
Any other use is prohibited; in particular, cutting excessi-
vely large branches, felling trees and cutting tree trunks
on trestles is prohibited.
These instructions contain information deemed necessary for
proper use, knowledge and standard appliance maintenance.
They do not include information on pruning techniques; the
user can find additional information in specific books or
publications or by attending specialised training courses.
COMPONENTS
Refer to fig. A and the following figures, attached to these
instructions.
1. Power supply plug and cable
2. Rear hand grip
3. Start/stop switch
4. Switch release button
5. Extension pole / Front hand grip
6. Telescopic tube adjustment ring nut
7. Rear handle fixing ring nut
8. Cutting head fixing ring nut
9. Locking pin
10. Oil tank cap
11. Housing
12. Electric motor cooling vents
13. Bar
14. Saw chain
15. Bar cover
16. Sprocket
17. Oil hole
18. Seat of the threaded pin
19. Bar fixing screw
20. Chain tensioning screw
21. Bar lower hole
22. Oil hole
23. Bar groove
24. Bar greasing hole
25. Chain tensioning pin
26. Hole for unlocking components
INSTALLATION
!
IMPORTANT! The manufacturer is not liable for any
direct and/or indirect damage caused by incorrect elec-
trical connections.
!
IMPORTANT! Before you perform the following steps,
make sure that the plug is disconnected from the AC
power supply.
!
IMPORTANT! Wear protective gloves.
TRANSPORT
Always use the packaging when transporting the tool; this
will protect it from impact, dust and humidity which can
compromise normal operation.
Shorten the length of the extension pole (pos. 6) to its
minimum length and slip the bar cover protection (pos. 15).
HANDLING
Always carry the tool with the engine off. Hold the tool with
both hands using both hand grips (pos.2-5), carry it by your
side, with the bar facing downwards and away from your body.
Keep it raised off the ground and do not let the tip drag on
the ground. Due to its considerable length, make sure you
do not hit feet, legs, persons or objects.
After use, set the tool down carefully without dropping it,
with the fuel tank cap facing upwards; avoid setting the tool
down on sloped inclines or on vehicles as it could roll off and
fall. Never set the tip on the ground, to prevent the bar from
bending until it becomes permanently deformed.
SWITCHING ON
When choosing where to use the power tool, the following
should be considered:
- the area must not be damp and there is no bad weather.
- the working area is sufficiently large and free from obstacles.
- the area is well lit.
- the tool is used close to the main differential switch.
- the power supply system is earthed and conforms with
standards (only if the power tool is Class I, and equipped
with a plug with earth cable).
- room temperature is between 10° and 35° C.
- the environment is not in a flammable/explosive atmosphere.
- there are no overhead power lines.
Take out the tool and its components and visually check
that they are perfectly intact; then proceed to thoroughly
clean them.