VALERA SYSTEMA 654.01, Инструкция по эксплуатации, Страница: 3 / 82

5
OPERATING INSTRUCTIONS
PARTS
1 Appliance
2 Hair cutting head
3 Switch
4 Charge light: red when charging, green when
fully charged
5 Socket for transformer
6 Base
7 Charging contact
8 Lubricant
9 Transformer
10 Head for body hair
11 Head for nose and ear hair
The appliance can operate either using mains power or in cordless mode, as it has a rechargeable
battery.
MAINS POWER SUPPLY
Connect the transformer the (fig.1 - ref. 9) by inserting the plug into the appliance socket (fig.1 - ref.5).
Plug the transformer into the mains.
Warning: if the appliance does not work with mains power when the battery charge has run down
completely, switch it off, recharge the battery for about five minutes and then switch back on again,
running on mains power.
RECHARGING THE BATTERY
• Before using the appliance for the first time, charge the battery for 24 hours. For subsequent charges,
allow the appliance to charge for at least 12 hours.
• Switch the appliance off using the switch (fig.1 - ref.3). The battery can only be charged with the
appliance switched off.
• Connect the transformer (fig.1 - ref.9) by inserting the plug into the appliance socket (fig.1 - ref.5).
Or connect the transformer to the base (fig.1 - ref.6) by inserting the plug into the base plug (fig.1
- ref.5), and rest the appliance on the contact (fig. 1 - ref.7).
• Plug the transformer into the mains.
• The charge light (fig.1 - ref. 4) turns red while the appliance is charging and reverts to green when
charging is complete.
• When the battery is fully charged, the appliance can be used for approximately 50 minutes without
connection to the mains.
• In order to optimise the lifetime of the battery, never charge the appliance for more than 24 hours.
• Discharge the battery completely every few months, then recharge it again. This optimises the
lifetime of the battery.
ADJUSTABLE GUIDE COMBS
The appliance is supplied with two hair/beard and moustache trimming combs, which can be adjusted
to offer different cutting lengths: from 2 to 8 mm and from 10 to 16 mm.
To adjust the guide comb, press the adjustment button (fig.1 ref.16) and slide the comb in or out until
it reaches the desired cutting length, as illustrated in fig. 2.
The various positions can be seen on the comb setting indicator (fig.1 ref.17).
The comb attachment can be removed by lifting the tab at the rear (fig.3); in this case the cutting
length is 1 mm.
To refit the comb attachment, slot the front in first (fig.4 - A), then press down on the rear (B).
The appliance is also supplied with an adjustable comb for body hair, with three different cutting
lengths: 2, 5 or 9 mm. For cutting length adjustment guidelines, see fig.5.
FITTING AND REMOVING THE HEAD
Please refer to fig.6 when removing the head. For instructions on re-fitting the appliance head, see fig.7.
USING THE HEADS
The appliance is supplied with 5 heads.
• Hair cutting head (fig.1 ref.2) - For trimming hair, can either be used alone or in conjunction with the
relevant combs (fig.1 ref.15).
12 Head for beard and moustache
13 Shaver head
14 Adjustable guide comb for body hair
15 Adjustable guide comb with 4 settings
16 Guide comb adjustment button
17 Guide comb setting indicator
18 Graduated comb
19 Barber’s comb
20 Moustache comb
21 Scissors
22 Cleaning brush
00060589 int aprile2013 04/04/2013 12.46 Pagina 5