Entry Delay Time
NOTE: When a disabled station is accessed, the
alert tone will be at a lower tone as a reminder
that the alarm at that station has been disabled.
If a key entry occurs at a door (an entry not using the
dialpad or remote button) the remote button must be
pressed or the confirmation code must be dialed on
the telephone keypad. This must be done within a
designated period of time after the door is opened
signifying a legitimate door opening or an alert will
sound. The default time for the confirmation press is
15 seconds. This time can be changed by:
To enable a door alarm that has been disabled:
1. Lift handset and receive dial tone.
2. Press 6.
3. Press station number (1-4) or * for all stations.
4. Receive dial tone.
1. Lift handset and hear dial tone.
Alert Tone
2. Press # 1 2 3 # 8.
3. Enter station number (1-4) or * for all stations.
The phone and station receives a ringback tone prior
to connection. Default - the station receives the tone.
To remove the alert tone:
4. Enter time length in seconds (0-999).
5. Press #.
6. Receive dial tone.
1. Lift handset and receive dial tone.
2. Press # 1 2 3 # 9.
Duration of Ringing
3. Enter station number (1-4) or * for all stations.
4. Press 0.
When a door button is pressed, it activates the phone
into a ring cycle. The ring cycle will continue for a
programmed time period and stop if unanswered.
5. Press #.
6. Receive dial tone.
To re-activate the alert tone:
1. Lift handset and receive dial tone.
The default equals approximately 30 seconds. To
change this default:
2. Press # 1 2 3 # 9.
3. Enter station number (1-4) or * for all stations.
1. Lift handset and receive dial tone.
4. Press 1.
2. Press # 1 2 3 # 5.
5. Press #.
3. Enter station number (1-4) or * for all stations.
6. Receive dial tone.
4. Enter ringing duration (1-255 seconds)
(0 = no time out)
Door Detect
5. Press #.
6. Receive dial tone.
Some door alarm contacts are closed when the door is
closed and some are open when the door is closed.
By default, the V-2904 uses door alarm contacts that
are open when the door is closed.
Disable Station Alarm
On power up, the station alarm condition is active. In
the event a doorway or gate would need to be left
open for an extended time (or at least longer than the
programmed time it can remain open before an alarm
condition), the alarm can be disabled.
To change this default:
1. Lift handset and receive dial tone.
2. Press # 1 2 3 # 0 1.
3. Press # and receive dial tone.
OPERATION
To leave door open without causing an alarm
condition:
When the doorplate button at a station is pressed,
interrupted ring voltage from the V-2904 initiates
ring-in on the telephone system and sends a
confirmation tone to the door. When the phone is
answered, a series of optional tones may be heard in
the receiver. These tones numerically indicate which
door is calling. These are followed by a ringback
tone and connection to the handsfree speaker. When
the phone is busy with one station and a call is placed
from another station, the person on the telephone will
hear a call waiting tone corresponding to the door
location. (Example: Station 2 - Beep-Beep).
Repeated button presses from the station will cause
repeated signals to the phone provided the presses are
separated by 5 seconds. If the 2nd call is not
answered during the programmed time (determined
by the programmed number of ring cycles) after the
last press, it will lose its power to be answered.
1. Lift handset and receive dial tone.
2. Press 5.
3. Press station number (1-4) to be disabled or *
for all stations.
4. Enter disable code (default is *; this may have
been changed).
5. Receive dial tone.
The default code for disabling the station alarm
condition is *. To change
this default:
1. Lift handset and hear dial tone.
2. Press # 1 2 3 *.
3. Enter station number (1-4) or * for all stations.
4. Enter up to 7 digits.
5. Press #.
6. Receive dial tone.
If the door is equipped with an electric strikeplate, a
10
