manualshive.com logo in svg

Valco Instruments Co. Inc. TCD, Инструкция по эксплуатации

Поделиться
Скачать
Valco Instruments Co. Inc. TCD Скачать руководство пользователя страница 3

Table of Contents

Introduction

Description and Operating Principle ............................................................... 1
Safety Notes and Information ........................................................................ 2
Components of the Detector System ............................................................. 3
Description of Controls and Connectors ......................................................... 4

System Requirements

Components Not Included with the Detector System ..................................... 7
System Purity ................................................................................................ 7
Recommended Carrier Gas Purifiers .............................................................. 7
Carrier Gas Selection ..................................................................................... 7
GC Column Selection ..................................................................................... 8

Installation

General Precautions ...................................................................................... 9
Mounting the Detector on the GC ................................................................... 9
Gas Connections .......................................................................................... 10
Column Connection ....................................................................................... 12
Electrical Connections .................................................................................. 13
Initial Power-Up ............................................................................................. 15

Troubleshooting

Troubleshooting Chart ................................................................................... 17
Heater Fault Determination ............................................................................ 17
Detector Fault Determination ......................................................................... 18

Maintenance

Bake Out Procedure ..................................................................................... 19
Disassembly and Cleaning ............................................................................ 19

Warranty ............................................................................................................. 20
Detector Performance Log ................................................................................... 21

Содержание TCD


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды