manualshive.com logo in svg

Valco Instruments Co. Inc. TCD, Инструкция по эксплуатации

Поделиться
Скачать
Valco Instruments Co. Inc. TCD Скачать руководство пользователя страница 10

6

MAINS POWER connector
For connection to 115/230 VAC source.

CHART OUTPUT connector
Normally connected to a strip chart recorder.  This output has an attenuated
range of 0-1 volt and 0 - 10 volts, with the signal scaled by the attenuation
factor set on the front panel.  The output also has an internal signal reference
(-) at zero volts.  For best noise performance, the shield (earth) and signal
reference (-) should not be connected together.

UNATTENUATED OUTPUT connector
Normally connected to a data acquisition system or other recording means.
For convenience, full-scale 0 - 1V and 0 - 10V outputs are provided, with an
internal signal reference (-) at zero volts.  For best noise performance, the
shield (earth) and signal reference (-) should not be connected together.

DETECTOR connector
For connection to the detector control and heating system.

NOTE: These terminals are for connection only to
equipment having no accessible live parts.

Introduction

Figure 4: Rear panel connectors

CHART

A

B

A-B

OUTPUTS

DETECTOR

SERIAL NO.

MODEL NO.

Valco Instruments Co. Inc.

MAINS SWITCH

MAINS POWER

CONNECTOR

DETECTOR

CONNECTOR

CHART OUTPUT

CONNECTOR

UNATTENUATED

OUTPUT

CONNECTORS

MODEL TCD2-C

115/230

175VA MAX.

T2.0A

250V

MAINS

Valco Instruments Co. Inc.

Made in USA by

Содержание TCD


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды