Vaisala MGP261 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 90

background image

4. Operating with Insight Software

4.1 Vaisala Insight Software

Vaisala Insight software is a configuration software for Indigo-compatible probes. The
supported operating systems are Windows 7 (64-bit), Windows 8.1 (64-bit), and Windows 10
(64-bit).

With the Insight software, you can:

• See device information and status.
• See real-time measurement.
• Configure serial communication settings, analog input and output parameters and scaling,

and environmental compensations.

• Calibrate and adjust the device.

Download Vaisala Insight software at

www.vaisala.com/insight

.

The probe can be connected to Vaisala Insight software using a Vaisala USB cable (no.
257295).

More Information

‣

Connecting to Insight Software (page 35)

‣

Insight Main View (page 37)

‣

Configuring Modbus Communication Settings with Insight (page 39)

‣

Configuring Analog Outputs with Insight (page 40)

‣

Configuring Environmental Compensations with Insight (page 44)

‣

Calibration and Adjustment with Insight PC Software (page 52)

4.1.1 Basic and Advanced User Modes

You can switch between the

Basic Mode

and

Advanced Mode

user modes with the selections

in the

Settings

menu.

Certain functionalities are only available in

Advanced Mode

. The options enabled by switching

to

Advanced Mode

are often intended for administrative users: set the user mode according to

the requirements of the personnel that use the device.

More Information

‣

Insight Main View (page 37)

MGP261 User Guide

M212273EN-A

34

«
...
34
35
36
37
38
...
»

Содержание MGP261



























































































Отзывы:

Нет отзывов

Похожие инструкции для MGP261

Бренд: janitza Страницы: 28

Бренд: Rayjet Страницы: 81

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Oceanic Страницы: 68

Бренд: Oceanic Страницы: 24

Бренд: Ulvac Страницы: 18

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: Badger Meter Страницы: 24

Бренд: Van Walt Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Бренд: SEFRAM Страницы: 31

Бренд: UEi Страницы: 5

Бренд: Anglerfish Creative Lighting Страницы: 15

MON08 MULTILINK

Бренд: P&E Microcomputer Systems Страницы: 16

Бренд: Delmhorst Страницы: 11

Бренд: Calypso Instruments Страницы: 9

Бренд: Kailiu Instrument Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды