manualshive.com logo in svg

Vaisala HUMICAP MMT310, Руководство пользователя

Поделиться
Скачать
Vaisala HUMICAP MMT310 Скачать руководство пользователя страница 39

Chapter 5 ________________________________________________________________ Operation 

VAISALA _______________________________________________________________________ 37 

High end adjustement

 

 

6.

 

After having made the low end adjustment, insert the probe head 
into a measurement hole of the high end reference chamber (e.g. 
NaCl: 75 % RH chamber in the humidity calibrator HMK15, please 
use the adapter fitting (13.5 mm)). Please, note that the difference 
between the two humidity references must be at least 50% RH. 

7.

 

Let the probe stabilize at least 30 minutes. You can follow the 
stabilization by pressing any key, typing C and pressing 

ENTER

. 

8.

 

When stabilized, type the high end reference value after a question 
mark and press 

ENTER

.   

>crh 
 
RH  :    11.25  Ref1 ? c 
RH  :    11.24  Ref1 ? c 
RH  :    11.24  Ref1 ? 11.3 
Press any key when ready ... 
 
RH  :    75.45  Ref2 ? c 
RH  :    75.57  Ref2 ? c 
RH  :    75.55  Ref2 ? c 
RH  :    75.59  Ref2 ? 75.5 
OK 

> 

OK

 indicates that the calibration has succeeded

 

9.

 

Take the probe out of the reference conditions and replace the 
filter. Take care to tighten the filter properly, recommended force 
130 Ncm. 

10.

 

If needed, give the calibration information (date and text) to the 

transmitter's memory, see the serial commands on page 29. 

11.

 

Reset the transmitter by giving a command 

RESET

. Transmitter 

returns to normal mode. 

Содержание HUMICAP MMT310
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды