Vaisala HUMICAP MMT310 Скачать руководство пользователя | Manualshive

Страница: 19 / 63

background image

Chapter 3 _________________________________________________________________Mounting

VAISALA _______________________________________________________________________ 17

NOTE

It is recommended that the supply is switched off, before connecting the
cable plug to the transmitter during installation or service/calibration.

Mounting the MMT317

The MMT317 has a small pressure-tight probe and it is ideal for tight
spaces with threaded connection. The small probe is installed using
the threaded fitting bodies, see below.

NOTE

Do not unsolder and then again resolder the sensor head cable from
and to the printed board during installation; this procedure may alter
the humidity calibration of the transmitter.

MMT317 with Swagelok Connector
for Tight-place Installations

Swagelok installation kit for the MMT317 includes Swagelok
connector with ISO3/8" thread ( Vaisala order code: SWG12ISO38)
or NPT1/2" thread (Vaisala order code: SWG12NPT12). See figure
below for MMT317 with Swagelok Installation Kit.

«
...
17
18
19
20
21
...
»

Содержание HUMICAP MMT310
































































Отзывы:

Нет отзывов

Похожие инструкции для HUMICAP MMT310

Бренд: Magnetrol Страницы: 16

Бренд: DINUY Страницы: 4

Бренд: Peiying Страницы: 24

HYPERVISIONT HV-300 Series

Бренд: Raymarine Страницы: 66

Бренд: RIDGID Страницы: 20

Бренд: Sennheiser Страницы: 8

Бренд: H-ITT Страницы: 2

Centronic / B-Tronic EasyControl EC715

Бренд: Becker Страницы: 144

Бренд: BriarTek Страницы: 10

Бренд: M-system Страницы: 3

Бренд: Invisible systems Страницы: 17

Бренд: DS Страницы: 39

Бренд: Kenwood Страницы: 52

Бренд: Icom Страницы: 64

Бренд: UTEPO Страницы: 2

Бренд: Microhard Systems Страницы: 16

Бренд: elero Страницы: 3

Бренд: elero Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды