Vaisala HMP7 Скачать руководство пользователя страница 49

Страница: 49 / 96

Error message

Description

Recommended action

Critical errors

Firmware checksum mismatch

Firmware is corrupted

Contact Vaisala technical
support

Factory default settings
corrupted

Parameter memory is
corrupted

Main configuration settings
corrupted

Additional configuration
settings corrupted

Device settings corrupted

Sensor coefficients corrupted

Non-volatile memory read
write failure

Hardware fault

Errors

Temperature measurement
error

Readings from sensors missing
or out of range

Inspect probe head and
sensors visually. If the probe is
completely wet, allow it to dry
out.
If the sensors are damaged or
missing and the error
message(s) stay active, contact
Vaisala to have the probe
repaired.

Humidity measurement error

Humidity sensor failure

Capacitance reference error

Hardware fault

Contact Vaisala technical
support

Ambient temperature out of
range

Probe body too hot or cold

Relocate the probe body so
that its ambient temperature is
within the specified operating
range

Supply voltage out of range

Supply voltage too high or low

Check supply voltage

Sensor heater failure

Hardware fault

Contact Vaisala technical
support

Warnings

Calibration certificate
checksum mismatch

Certificate stored in the probe
has an invalid checksum

Contact Vaisala technical
support

Calibration has expired

Shown by calibration reminder
functionality

Calibrate the probe and update
the calibration date information

Supply voltage too low for
probe heating

Probe heating enabled but
supply voltage is too low to use
it

Check supply voltage

Chapter 7 – Troubleshooting

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Содержание HMP7

































































































Результаты поиска

Содержание HMP7

Отзывы:

Vaisala HMP7, Руководство пользователя, Страница: 49 / 96

Результаты поиска

Содержание HMP7

Отзывы: