Vaillant VIH S GB 210/2 S страница 27 Скачать руководство пользователя

Страница: 27 / 72

Instructions on commissioning, maintenance, and troubleshooting for auroSTOR 0020111119_02

6.2.4 Venting the solar circuit

Danger!

Risk of burns and scalds resulting from
escaping hot steam!

Hot steam can discharge from automatic
air vents which are not shut off if the sys-
tem is
in stagnation.

Use automatic air vents with a
manufacturer's release to at least 150 ºC.

Shut off the automatic air vents when
operating the system.

Caution!

Malfunction due to air vents that are not
shut off!

Vapourous solar fluid can escape from
automatic air vents which are not shut off
whilst the system is in stagnation. The loss
of solar fluid results in functional problems.

Close all automatic air vents once ven-
ting is complete.

Caution!

Malfunction due to unsuitable air vents!

Unsuitable air vents can be destroyed in
solar mode.

Only use Vaillant automatic air vents
with
a manufacturer's release to at least
150 ºC.

Solar circuit filling with

Venting via

Vent opening

for flat collectors

Automatic air vent

with stop cock

Automatic

air separator system

Hand pump

Absolutely vital

Alternative

Recommended

Motorised filling pump
(maximum flow rate of
< 10 l/min)

Motorised filling pump
(maximum flow rate of
> 10 l/min)

Not necessary

Recommended

Tab. 6.3 Selection of venting method in accordance

with filling type

Installation 6

Содержание VIH S GB 210/2 S









































































Результаты поиска

Содержание VIH S GB 210/2 S

Отзывы:

Похожие инструкции для VIH S GB 210/2 S

Бренды по названию

Популярные бренды

Vaillant VIH S GB 210/2 S, Руководство пользователя

Результаты поиска

Содержание VIH S GB 210/2 S

Отзывы:

Похожие инструкции для VIH S GB 210/2 S

Бренды по названию

Популярные бренды