background image

33

Installation and maintenance instructions ecoTEC 0020029173_01

7.2.1 

Setting the heating partial load

The output of the boilers is set at 35 kW in the factory. 
You can specify a value that corresponds to the kW 
output of the boiler under diagnosis point "d. 0“.

7.2.2  Setting of pump overrun and pump operating 

mode

The pump overrun time for the heating operation is set 
at the factory to a value of 5 minutes. It can be adjusted 
through a range of 2 – 60 minutes under diagnosis point 
"d. 1“. Under diagnosis point "d.18“, you can set the 
overrun behaviour of the pump to a different mode.

Overrun:

 Once the heating requirement has ended, the 

pump runs on for the time specified under "d. 1“.

Run on:

 The pump is switched on if the rotary knob for 

setting the heating flow temperature is not at the 
left-hand stop and the heat requirement is enabled by 
an external controller.

Intermittent: 

This pump operating mode is useful for 

removing residual heat after charging when the heat 
demand is extremely low and large temperature 
differences exist between the charging and heating 
mode target values. This avoids underheating of the 
living spaces. In the event of a heat demand the pump is 
switched on every 25 minutes for 5 minutes once the 
overrun time has elapsed.

7.2.3  Setting of maximum flow temperature

The maximum flow temperature for the heating is set at 
the factory to 75 °C. Under diagnosis point "d.71“ it can 
be set to between 40 and 85 °C.

7.2.4  Setting of burner blocking time

To prevent frequent switching on and off of the burner 
(energy loss), an electronic restart lockout is activated 
for a specific period each time the burner is switched 
off. The burner locking time can be modified to suit the 
conditions of the heating installation.
The burner blocking time is only activated for the 
heating operation.
Hot water operation during a burner blocking time does 
not affect the timer. The maximum burner locking time 
can be set to a value of between 2 and 60 min under 
diagnosis point d.2 (factory setting: 20 min). The 
individual effective blocking time is calculated from the 
current target flow temperature and the set maximum 
burner blocking time.
The timer can be reset or cancelled by pressing the fault 
clearance key and also by activating summer mode for a 
short time (by briefly turning the nominal flow 
potentiometer to the left-hand stop then back to the 
starting position). The remaining burner locking time 
following a regular shutdown in heating mode can be 
called up under diagnosis point "d.67".

Adapting the boiler to the heating system 7

Содержание ecoTEC VU 656/4

























































Отзывы: