background image

5

Operating manual atmoCRAFT

 Caution!

Any improper use is forbidden.

The appliances must be installed by a heating engineer, 
who is responsible for adhering to the existing 
regulations, rules and guidelines.

3.3 

Requirements of the installation site

The Vaillant gas heating boilers atmoCRAFT must be 
installed in boiler rooms. Ask your heating engineer 
which national regulations must be observed.
The entire installation site should be frost-proof. 
Observe the specified frost protection measures in 
section 4.10 if you are unable to ensure this 
requirement.

 Note!

It is not necessary to keep a clearance between 
the appliance and combustible materials or 
components, since at the rated heating power 
of the appliance the temperature at the surface 
of the housing is always lower than the 
maximum allowed temperature of 85 °C.

3.4 Care

•  Clean the exterior of your appliance with a damp cloth 

and a little soap.

 Note!

Do not use scouring or cleaning agents, which 
might damage the exterior or plastic controls.

3.5 Recycling 

and 

disposal

Both your Valliant atmoCRAFT gas boiler and its 
packaging consist mainly of recyclable raw materials.

3.5.1 Appliance

Do not dispose of your Valliant atmoCRAFT gas boiler or 
any of its accessories with household waste. Make sure 
the old appliance and any accessories are disposed of 
properly.

3.5.2 Packaging

Please leave the disposal of the transport packaging to 
the qualified servicing company which installed the 
appliance. 

 Note!

Please observe the applicable national legal 
regulations.

3.6 

Energy saving tips

Installing a weather compensator

Weather compensators regulate the heating supply 
temperature according to the outside temperature. No 
more heat is created than is required. The designated 
heating feed temperature for the corresponding outside 
temperature must be set on the weather compensator. 
This setting must not be greater than that required by 
the design of the heating installation.
The correct setting is normally undertaken by the 
heating engineer. The desired heating and set-back 
phases (e.g. at night) are automatically turned on and 
off using the integrated time programmes.
Weather compensators combined with thermostat valves 
are the most economical form of heating regulation.

Reducing the heating system

Reducing the room temperature at night and in your 
absence. This is best and most reliably realised using 
regulators with customisable time programmes.
At such times, set the room temperature approx. 5 °C 
lower than during full heating times. Reduction of more 
than 5 °C brings no additional energy saving, because 
then increased heating capacities would be needed for 
the next full heating period. Only for longer absences, 
e.g. holidays, is it worthwhile to further lower the 
temperatures. However, in winter, make sure that there 
is adequate frost protection.

Room temperature

Set the room temperature only as high as would be 
enough for your comfort level. An extra degree would 
mean increased energy consumption of about 6%.
Adjust the room temperature according to the purpose 
of use of the room. For example, normally, bedrooms or 
seldom used rooms are heated to 20 °C.

Setting the operating mode

In warmer seasons, when the apartment needs no 
heating, turn the heating to summer mode. The heating 
mode is then shut off, however, the device or the plant 
remains ready for operation for water heating.

Uniform heating

Often, in an apartment with central heating, only one 
room is heated. Through the encapsulation surfaces of 
this room, i.e. walls, doors, windows, roofs, floors, the 
unheated adjoining rooms are also heated in an 
uncontrolled manner, i.e. heat energy is lost 
inadvertently. The capacity of the radiator in this one 
heated room is obviously not enough for such an 
operating mode.
Consequently, the room cannot be heated adequately 
and an uncomfortable feeling of coolness prevails (the 
same effect is produced when doors between heated 
and unheated or partially heated rooms remain open).
This is incorrect saving: The heating is in operation and 
still the room temperature is not comfortably warm. 
Greater heating comfort and a more practical operating 

Notes on the installation and operation 3

GB

Содержание atmoCRAFT VK SERIES


















Отзывы: