background image

20

 

 

7.5.2  Event Logs 

In the submenu Event Logs all the Logging events are listed. For example, when the Actual shaft Power 
is exceeding the EEXI Power limit, the event will be listed in this Event log menu. 
The user can Verify an event by touching the 

Verify event

 button. In this submenu the Start time and 

End time will be shown. You can choose a reason why the power reserve is used. 
 
The following pre-set reasons can be chosen: 

Weather or ice-conditions 

Saving a life at sea 

Pirate avoidance 

Maintenance 

Other (please fill in below) 

 
This can only be done once the logging state has been left. 
It is possible to add Additional information to the Event log. 
 
 

 

 

Figure 20 

– Event Logs, event log not verified yet

 

Figure 21 

– Verification of the event log Power above limit

 

 
 
When the event is verified by selecting a reason, the red cross (

) turned into a green checkmark (

)

It is possible to print the report of the Event Log via a connected external PC. If no printer is available 
you could download the Event Report as a PDF-file and save it. 
In the Shaft power limitation Event Report important data like Ship IMO, Duration of Power reserve, Start- 
and end time, start- and end position and the reason of the Power reserve use. An Example of an Event 
Report is shown in the attachment. 
 
 

 

 

Figure 22 

– Event log is verified and could be printed

 

Figure 23 

– Shaft power limitation event report

 

 
 

 
 

NOTE:  

Downloading the report as PDF is not possible with browser Internet Explorer.

 

 
 

Содержание Shapoli 620





































Отзывы: