background image

Vacuuming

Inserting the hose

The hose connects to the system through the utility valve 

inlet on the front of the unit by lifting the door open and 

inserting the hose. (Fig. 1)
See below for using your attachments & cleaning tools.

On/Off Switch

Insert the hose before turning the unit on.  

The system is turned on and off by flipping 

the switch on the side of the unit.

Blowing

The exhaust will operate as a light blower for your shop 

or garage. This feature does not replace a leaf blower. 

(Popping noise & some air leakage is common.)

To operate the blowing feature:

Attach the hose to the black Exhaust/Blow Stem located 

on the side of the unit.  (Fig. 2)

For this feature to operate, you must also open the utility 

valve on the front of the unit and insert the additional 

cuff that is included with your system.  (Fig. 3)  This must 

remain inserted to hold the door open for the blow 

feature to work.
When finished, turn off the unit first, then remove both 

the hose and cuff from the two inlets.

USING YOUR SYSTEM

6

2

1

3

USING YOUR ATTACHMENTS & CLEANING TOOLS

CLEANING TOOLS

All cleaning tools will attach to either 

the hose end or the telescopic wand by 

pushing firmly onto the end.

a) Upholstery Tool

 

Works well for cleaning 

car upholstery & carpet.

b) Crevice Tool

Reach into cracks and 

crevices that are  

hard to reach.

c) Dusting Brush

Use for dusting shelves, 

tables, dashboards, etc.

Hose Hanger

  

Loop hose on hanger 

approx. 4-5 times or loop hose on floor and 

then pick up and hang on hanger.

Telescopic Wand

  

Provides you extra length for floor  
cleaning or reaching high areas.

To use:

 

Adjust by a) twisting the ratcheting 

mechanism in the middle of the wand to release 

and extend.  Twist back to tighten. b)  Adjust by 

pressing down on the ratcheting mechanism in 
the middle of the wand to release and extend. 

Floor Brush

  

For cleaning light dirt & dust 

on hard floor surfaces.  

To use:

 Attach to telescopic 

wand and go back and forth 

over the area to be cleaned.  

Do not force the front of 

the brush down when moving forward.  Allow the 

brush to gently glide across the floor to pick up 

larger debris.  

(FT220 floor tool is recommended for larger debris. Sold separately)

a

b

Содержание GARAGE VAC













Отзывы: