Vacmaster vmVF1515HJ, Руководство пользователя

Страница: 7 / 11

W
Et-vACUUm OpERAtiON
WARNiNG: BE SURE tO READ, UNDERStAND, AND AppLY iNFORmAtiON,
ENtitLED ‘SAFEtY iNStRUCtiONS & WARNiNGS’. DO NOt vACUUm iN
AREAS WitH FLAmmABLE GASES, vApORS, OR ExpLOSivE DUStS iN tHE
AiR. FLAmmABLE GASES OR vApORS iNCLUDE BUt ARE NOt LimitED tO;
LiGHtER FLUiD, SOLvENt tYpE CLEANERS, OiL-BASE pAiNtS, GASOLiNE,
ALCOHOL OR AEROSOL SpRAYS. ExpLOSivE DUStS iNCLUDE BUt ARE NOt
LimitED tO; COAL, mAGNESiUm, GRAiN OR GUN pOWDER. tO REDUCE tHE
RiSK OF HEALtH HAZARDS FROm vApORS OR DUSt, DO NOt vACUUm tOxiC
mAtERiALS.
WARNiNG: DO NOt pLUG iN pOWER CORD tO pOWER OUtLEt, mAKE SURE
pLUG iS DiSCONNECtED BEFORE ASSEmBLiNG tHE WEt/DRY vAC
1. Verify that the power cord is disconnected from the outlet. Verify that the container
is clean and free of dust and dirt. (fig. 1)
2. Remove cartridge filter and the dust collection bag, then carefully install the foam
sleeve filter over the filter cage and place the power head back on the container.
(fig. 2) See filter installing instructions on page 10.
Do noT USE THE CarTrIDgE fIlTEr for lIQUID VaCUUmIng.
opEraTIng InSTrUCTIonS – WET VaCUUmIng
3. Fit the desired extension wands or nozzle to the vacuum hose. (fig. 3)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord
into the outlet. (fig. 4 & 5)
5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig. 6)
6. After use, flip the switch to the ‘O’ OFF position and unplug the power cord from
the outlet. (fig. 7 & 8)
7. Empty the container into a suitable receptacle or drain. (fig. 9)
8. To rewind the cord, hold on to the plug and press the cord rewind button. Do not
allow plug to whip when rewinding. (fig. 10)
impORtANt! When vacuuming large quantities of liquids, do not immerse the
nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to
allow air inflow. The machine is fitted with a float valve that stops the suction
action when the container reaches its maximum capacity. you will notice an
increase in motor speed. When this happens, turn off the machine, disconnect
from power supply, and drain the liquid into a suitable receptacle or drain.
To continue vacuuming, refit the container with power head. after wet
vacuuming, turn the machine off and remove plug from power supply. Empty
the container, clean and dry the inside and outside before storage.
REmEmBER!
The foam filter must be removed after wet vacuuming, and a
cartridge filter must be installed before dry vacuuming again.
3
8 9 10
1
2 5 4
6 7
m
AiNtENANCE
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Disconnect the hose from the vacuum. (fig. 2)
3. Undo the latches and remove the power head from the container. (fig. 3)
4. Clear all dirt or debris from the container and hose. (fig. 4)
5. Clean the foam filter by washing it with water and mild soap. (fig. 5)
6. Check the hose, attachments, and power cord to verify that they have not been
damaged.
impORtANt! Clean or change the cartridge filter regularly for best
performance. alWayS USE CarTrIDgE fIlTEr for Dry VaCUUmIng. If the
machine is used with out the cartridge filter, the motor will burn out and the
warranty will be voided. always keep spare filters on-hand.
NOtiCE! The filters included are made of high quality materials designed to
stop small dust particles. The cartridge filter should be used for dry pick-up