E
N
G
L
IS
H
8
SELECTING THE CHANNEL AND THE
MONOSTABLE / BISTABLE OPERATION LOGIC
Select the channel and the operating logic by referring to the
following table:
1.
Press the SW1 key of the receiver N times, as indicated
above: the relevant led goes on
2.
Within 5 seconds, press and hold the button on the remote
control.
-
if the remote control unit is a ROYAL version, the
procedure ends at point 3
-
if the remote control unit is a PERSONAL PASS version, go
to point 4 and follow the procedure until the end of the
section
3.
LED on the receiver is turned off to indicate the code has
been memorised correctly
4.
The led of the receiver goes out and goes on again: the code
has been memorised and the receiver remains standby for 5 s
with a new code to be memorised
5.
Memorise all the remote control units necessary
6.
After 5 seconds without a valid transmission, LED L1 is turned
off and the receiver returns to normal operating mode
PROGRAMMING THE TIMER FUNCTION
To memorise a transmitter on channel 1, associating it with the
TIMER function, proceed as follows:
1.
Press and hold the SW1 key on the receiver:
LED L1 (associated with the first channel) comes on
2.
After 4 seconds, LED L1 is turned off
3.
When led L1 goes off, release the SW1 button. Led L1 starts
a sequence of flashings at low speed (1 flash per second).
The number of flashing corresponds to the time which can
be set as shown in the table.
4.
The number of flashes for LED L1 corresponds to the period
of time it is desired be set.
5.
Press button SW1 on the receiver during the desired period of
flashing: the series of flashes in interrupted and LED L1
remains on
6.
Within 5 seconds, press and hold the button on the remote
control:
-
if the remote control unit is a ROYAL version, the
procedure ends at point 7
-
if the remote control unit is a PERSONAL PASS version, go
to point 8 and follow the procedure until the end of the
section
7.
LED L1 on the receiver is turned off to indicate the code has
been memorised correctly
8.
LED L1 on the receiver is turned off and then comes on again:
the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
9.
Memorise all the remote control units necessary
10.
After 5 seconds without a valid transmission, LED L1 is turned
off and the receiver returns to normal operating mode
To memorise a transmitter on channel 2, associating it with the
TIMER function, proceed as follows:
1.
Press and release the SW1 key: LED L1 comes on
2.
Press and release the SW1 key: LED L3 also comes on
3.
Press and hold the SW1 key: LEDs L1 and L3 are turned off
and LED L2 comes on
4.
After 4 seconds, LED L2 is turned off
5.
When led L1 goes off, release the SW1 button. Led L1 starts
a sequence of flashings at low speed (1 flash per second).
The number of flashing corresponds to the time which can
be set as shown in the table.
6.
The number of flashes for LED L1 corresponds to the period
of time it is desired be set.
7.
Press button SW1 on the receiver during the desired period of
flashing: the series of flashes in interrupted and LED L1
remains on
8.
Within 5 seconds, press and hold the button on the remote
control:
-
if the remote control unit is a ROYAL version, the
procedure ends at point 9
-
if the remote control unit is a PERSONAL PASS version, go
to point 10 and follow the procedure until the end of the
section
9.
LED L1 on the receiver is turned off to indicate the code has
been memorised correctly
10.
LED L1 on the receiver is turned off and then comes on again:
the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
11.
Memorise all the remote control units necessary
12.
After 5 seconds without a valid transmission, LED L1 is turned
off and the receiver returns to normal operating mode
N° Flashing
Time
1
01 sec.
2
02 sec.
3
03 sec.
4
04 sec.
5
05 sec.
6
06 sec.
7
07 sec.
8
08 sec.
9
09 sec.
10
10 sec.
11
11 sec.
12
12 sec.
13
13 sec.
14
14 sec.
15
15 sec.
16
30 sec.
N° Flashing
Time
17
1 min.
18
1,5 min.
19
2 min.
20
2,5 min.
21
3 min.
22
3,5 min.
23
4 min.
24
4,5 min.
25
5 min.
26
5,5 min.
27
6 min.
28
6,5 min.
29
7 min.
30
7,5 min.
N°IMPULSES
SW1
LED ON
L1
L2
L3
CHANNEL 1 MONOSTABLE
1
•
CHANNEL 1 BISTABLE
2
•
•
CHANNEL 2 MONOSTABLE
3
•
CHANNEL 2 BISTABLE
4
•
•
Содержание Wally2-230V
Страница 3: ...Fig 2 ...
