background image

1 of 34

03103436-A10030 Rev. B

Service 

Guide 

Contents

Safety Considerations...............................................................................................................2

AC System Overview.................................................................................................................3

Procedures .................................................................................................................................4

Blower Motor ..........................................................................................................................4

Control Head ..........................................................................................................................5

Condenser..............................................................................................................................7

Dryer ......................................................................................................................................7

Binary Switch .........................................................................................................................9

Hose Replacement...............................................................................................................10

Pressure Transducer ............................................................................................................12

Plenum .................................................................................................................................13

Internal Servo Motors ...........................................................................................................17

Passenger Side Vent ...........................................................................................................20

Heater Valve and Servo Motor .............................................................................................20

Evaporator and Heater Core Assembly ...............................................................................22

Heater Core..........................................................................................................................27

Evaporator Coil ....................................................................................................................31

Test System .............................................................................................................................34

Heater with Air Conditioning

2019 and Later Aeromaster

NOTICE

The information in this document is generic.  Details in illustrations and procedures 

may differ from those in your vehicle.  Because Utilimaster manufactures many different 

customized vehicle bodies, this document cannot list and illustrate every possible option for 

every vehicle.  Nevertheless, the most common body options are described here.  Use this 

information as a guideline where it applies.  Refer also to the separate chassis operator’s 
guide supplied by the chassis manufacturer.

Содержание Aeromaster 2019



































Отзывы: